Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello
Is is possible to enable MCUBoot image compression on nRF52832 ?
I tried to enable it following this blog post but I got a compilation error :
Compiler insulted...
I am using peripheral_uart as my base project. Right now MTU value is 23 I believe as I can receive only 20 bytes of data at a time. How I can increase the MTU size with configurations...
Hello,
in use is the nrf connect sdk v2.6.2 toolchain v2.6.2 on my nrf5340DK
I struggle transmitting ADC data from my nrf5340DK via USB to my windows PC. On my PC there...
I've added some debug information to the build of my application. The added stack usage has caused some threads (USB, BLE) to overflow the stack and cause random crashes....
Hi,
Is there any better block diagram of how power is managed and routed within the nRF7001/ nRF7002 device ?
I see it has a buck from BUCKVBAT fed back to several other...
When trying to open certain c or h files in my project, Segger Embedded Studio (latest version) gives a very longwinded uncopyable dialog message that there was an error decoding...
Reopening this issue from three years ago
as the original question was not answered.
So I had this line of code after sd_softdevice_is_enabled 'returns' false
but...
I am trying to communicate with multiple devices using ESB. The host device must queue data in the TX FIFO as ACK data before receiving the data. I want to keep data queued...
Hello! I am developing an application under the SDK V2.9.0. Now I am trying to set up a simple project with a sysbuild, Mcuboot and a partition manager. Here is the file tree...
Hi,
I’m currently using nrfx libraries when there are no equivalent options in Zephyr drivers, and I found similar drivers with the nrfy prefix. What are the differences...
Hi
I would like to use DeviceTree in VS code. The VS code had installed "nRF Connect for VS Code Extension Pack" and tools chain.
But I can't see any file in "DEVICETREE...
Hi Nordic DevZone Support,
I am facing an issue with my custom PCB using the nRF52840 microcontroller and Zephyr NCS v2.6.1 . The same firmware works on other PCBs , but...
Hello, I am working on nRF52840 and using nRF Connect SDK v2.9.0.
I want to know how I can configure the UART to be half-duplex tx or half-duplex rx.
I checked the APIs...
Hello Nordic supporters!
We are developing a system using BT Mesh alongside a software DALI protocol driver with certain timing requirements.
Right now we're trying...
Hello,
I am trying to build the Wi-Fi Bluetooth LE coexistence example using the nRF54L15 DK and nRF7002 EB, but I encounter the following error: zephyr_pre0.elf section...
