Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
I think the new MCP might have a bug somewhere. I have not been able to find out the exact sequence on how to provoke it, but I have to restart the application more often...
if I set BLE_GAP_CONN_SEC_MODE_SET_OPEN, I can get data,
but if I set BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM,
Three different even sequences happened, only one sequences...
Hi,
I disconnect the BLE by calling *sd_ble_gap_disconnect*(), and found that it run to *app_error_handler*() after the BLE_GAP_EVT_DISCONNECTED event occured, and I don...
I program the nRF2727 module with the "Block readback of mainmemory" seleted using nRFgo studio tool.
After that, I can still read out the content of flash. What's the root...
As per this thread: devzone.nordicsemi.com/.../question-regarding-hfclk-control the SD stack takes care of HFCLK, however as fas as I understand HFCLK is also responsible...
Hi,
I use the DTM for the production test, I use the transmitter test ,with canal 19 (frequency = 2438MHz).
What is the tolerance of the frequency do you recommend (Min...
Hi all
i am working on Student Response System in which there multiple Transmitter and one Receiver and i want Receiver(nRF24lu1p) to behave as HID device.
Can any one provide...
I just buy a set of nRFgo starter kit . One pin of the display module (nRF6350) was destoryed, and the correspoding hole of P6 in the motherboard was inserted with short pin...
Hi,
I have some questions about how BLE scanning works that haven't been answered clearly anywhere I can find, (except no-doubt the Bluetooth Spec/Tome):
What...
You can not build out " the arm c c + + compiler has stopped working " in Keil uVision5.
PC of lenovo made in (Windows7 environment ) ,
By introducing development environment...
Hello everyone,
thx in advance for answers.
there is limitation written for 6.0.0 as follows:
Synthesized low frequency clock source is not tested or intended for use...
Hi everyone,
Is there any information about the (approx.) amount of erase/write cycles the nRF51 flash memory can handle?
I'm using the NVMC to store large buffers that...
hi:
when use the gzll for host, the power consumption is large, about 12mA , but the device mode just 38uA. I find in host mode the main loop always be awakened even if there...
