hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
I am running the examples l9_e5, l9_e5_sol and l9_e5_nrf5340_both_sol from this repository: https://github.com/NordicDeveloperAcademy/ncs-inter/tree/main/v2.9.0-v2.7.0/l9...
Hi,
i am working with the following setup:
- nrf5340
- SDK 2.6.3
- Direct Test Mode example with serial communication
I see that DTM example has changed from 2.1...
Hi Nordic team,
I'm implementing a BLE UART bridge (emulating the old SPP profile) using a custom service. The central device (dongle) I'm using only supports the classic...
Hi guys,
I am following DevAcademy lessons on nrf52833dk kit. I am testing the software on VsCode. SDK version is 2.7.0 and toolchain is 2.7.0. Board target is selected...
Dear, I'm developing on nordic 52840 with ncs2.6.1.
I found that the Current will reach to 600+uA in k_sleep state by enable SPI in device_tree and if i disable the spi...
Hi Nordic Team,
I am working on matter-based product development using nRF54L15 and looking for machine learning support for the same SoC. Can you please confirm if machine...
How do I adjust the swd speed used by nrf connect RTT ? Currently it is 2000khz but more is needed. I need to transfer audio data to PC.
For some reason my current process...
I saw in nrf connect sdk 2.9.1 that there was nRF54L15 sample code for Channel Sounding and nRF52833 DK sample code for Direction finding.
But now I want to implement...
Hello,
I am attempting to configure the following setup to support (with an nRF5340 + nRF7002-EK)...
1. nRF7002 on SPI w/ TLS, STA, and FW patches offloaded to QSPI...
Hello,
I am using PAwR (Pe riodic Adve rtsing with Response) in coded PHY (S8) with SDK 2.7.0, following the Nordic demo :
8562.PAwR_Demo.zip
Periodic Advertising with...
Hi all,
I'm working on a BLE peripheral using Zephyr and have run into an issue when enabling both dynamic device naming and long advertising intervals.
I enabled dynamic...
Is there a way to test that the RXD and TXD pins are sending and receiving data on the nrf5340? I am trying to connect these pins to the u-blox ANT-B10-00C using male to female...
Hi guys,
we are using the nRF52833 and have a running application. Now I want to introduce unit tests and stumbled upon ztest . The idea is to add a folder where all the...
I'm using nrf52832 developing my application.
In the past I used sd_ble_opt_set() to set a static pairing code for pairing.
But now a new requirement has emerged, I need...
