I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
We have a product with a microphone with PDM output that uses the nrf9160. The nrf9160 does have a PDM hardware unit that looks well suited to read it out. But currently there...
Hi Community Members,
I have a nRF51822 SoC custom board on which i have successfully tried flashing the executable file using openocd commands over Linux environment...
After the rewrite of persistent storage in SDK For Mesh v4.0.0 the code no longer does any basic sanity checks on the data read back from the flash.
The code below is from...
Hi
I am evaluating the serial_lte_modem sample with pc as client but failed, could you share the cmd format for gps start function?
here is the log after I issued the...
Hi guys, I'm facing the next problem:
I am using the Android BLE Library and Android-nRF-Mesh libraries. I connect my Android application to 8 nodes. One of those nodes...
To perform dfu using nrfutil, we need to bring wpantund service down in order to provide serial port to nrfutil. That restrict me to communicate with end nodes. Can you please...
Hi Nordic people,
According to my knowledge SPI can not verify the bits whether it is properly sending or not(like ack),speed wise is SPI ok,And in nordic nRF52840 have...
Hi!
I'm trying to use the LIS2DH12 driver on SDK 16.0.0 in SES. I've managed to read the correct value of who am i register. I'm trying to configure the sensor using LIS2DH12_DATA_CFG...
I have set up 2 nrf52 dev kits: one central and one peripheral. The peripheral side hits the PM_EVT_CONN_SEC_FAILED event about 30 seconds after the connection was established...
I'm trying every permutation.
Pressing IF BOOT/RESET button along with BUTTON 4 and powering off and on the board ... then letting the buttons go
There is a reset...
Hello,
it would seem that the Spi Slave example provided with the SDK 12.3.0 does not work correctly for the nRF51DK. Setup:
Master SPI : STM30G070CB Slave SPI : nF51DK...
Good day,
I have a problem with a custom board I have designed. It does not advertise the BLE device when programmed. I am testing with the simple ble_blinky and the nrf_connect...
I have nrf52840 development boards, when I ran DFU example (from NRF SDK for thread and zigbee v4.0.0) on autocommissioning true on 2 boards and was able to run it successfully...
Hi,
Is there any way to disconnect the NRF Toolbox connection through code. I tried to do the same but once ble turns back on its connecting back to NRF toolbox.
Hello,
I'm using (nRF 52840)Laird BL654 Module. I want to test PA/LNA Features Without a Soft device. please Suggest me how to test.
Regard's
-Nikunj Patel
