As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
I have made a state machine in which
I first initialize gpios, power management, clocks, and ble stack
I then put nrf into deep sleep (System OFF) state
A wakeup signal...
Does the http FOTA_download client support 301 responses, ie permanent redirects? I want to move the download file from a hired space to our server. Is using permanent redirects...
Previously I have been successful getting the AWS FOTA update working using the AWS FOTA example project, the example update.bin file and location provided
by Nordic for...
Hello there,
I am working in my master degree project with nordic NRF51822 microcontroller, but I faced two problems. I don't know if is a SD problem or hardware problem...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LE_TEST_END in DTM.
I tested with nRF52832...
Hi!
I have old code written in nRF51 enviorment with SDK nRF5_SDK_12.0.0.
I've successfully flashed the softDevice (s130_nrf51_2.0.1_softdevice.hex).
No error occurs...
hi, I am fresher starting my carrier in ASIC i am learning about UART where i come across with the word "DEADBEEF" in the coding please help me with where it is used and how...
Hi We've been using SDK12.1 with softdevice 3.1.0 on a NRF52832 for some time now. Now we want to upgrade our SDK to 15.2 with softdevice 6.1.0. We've converted the application...
Hi all,
I am working on nRF52840, nRF5_SDK_15.2.0, pca10056,usbd_cdc_acm
I can now communicate nrf52840 with PC,However, I failed to connect nrf52840 to android, Android...
Dear Team,
Greetings !!!
Device - nRF52832 Softdevice - s132_nrf52_6.0.0 IDE - segger embedded studio Bootloader - secure bootloader
In our current application, We are...
Hi,
We have build complex application based on Nordic SDK. Right now we are thinking about moving to Zephyr OS. I was wondering if there is any tutorial/tips I can find...
Hi, I'm using nrf52832 development board. In which i have flashed hci_uart example code of zephyr (latest code taken from https://github.com/zephyrproject-rtos/zephyr ) which...
Hello,
Our product is configured to use 3 total GPIOTE channels –– 2 sensors configured for "high accuracy" GPIOTE events, each around 10Hz refresh rate, and 1 using "low...
Current consumption during k_cpu_idle() after GPIO interrupt does not take the same value. Why does this happen? Any idea? Thank you for reading this post in advance.
<Environment...
hi all, i'm using uart with easyDMA, and i'm disabling and enabling it back on my code. before disabling the uart TX and RX works fine. after disable&enable i get wrong data...
