Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Hi,
I am currently developing a project using the nRF52810 as my controller, with SEGGER Embedded Studio (version 5.42a) and SDK version 17.0.2 as my development environment...
TLDR: Turn off your antivirus if you have the same error...
Hi everyone,
I'm trying to install nRF Connect v2.6.0, using either: - VS Code + nRF Connect extension (...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
I have bought an nRF52840 to sniff BLE packets. I have followed the user guide v4.1.x to install all SW on Windows 10 : So far I have downloaded nRF Sniffer for Bluetooth...
Hi,
This might be a simple one, but i cannot figure it out.. How do I place the rx/tx/rts/cts lines from UART0 on a GPIO1 pin?
In the piece of DTS below, 'tx-pin' is on...
nrf Toolchain: 2.7.0 nrf Connect SDK : 2.7.0 Gateway: nrF5340 Audio DK Headset: E arbud 'MOMENTUM TW 4' (Sennheiser) I try to run and test this following application Unicast...
Hi!
In my project i am using a motion sensor that uses a custom protocol. This has resulted in needing to implement bitbanging for it to work. The issue with this is that...
Hi,
I want to obtain the nrf52833‘s’ temperature with the SoftDevice enabled, and I have designed the code with reference to the example project. However, once the temperature...
Hi there,
I am trying to get nRFConnect working in VSCode, but when i click on things in the welcome screen it only shows "activating extensions..." in the bottom bar. I...
1) On p. 55 of nRF52805_PS_v1.4.pdf, section "5.3.8 Reset behavior" shows that a pin reset will reset GPIO, so will a pin reset active low also reset PSELRESET registers,...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hi,
I have built and run the MQTT sample for an nRF7002-DK and had it work as expected (connect, publish messages to test.mosquitto.org).
Now I'm trying to get that sample...
I created a new application using the "Create a new application" > "Copy a sample" > "zephyr/samples/basic/blinky" option in vscode. And I added a new build configuration...
