Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
Hi. I'm trying to flash the Cell Fund Lesson 4, Exercise 1 app – Reading buttons and controlling LEDs over MQTT, to an Icarus IoT Board v2 using the Actinius I/O Serial Programmer...
Hye,
using the nrf 2.4.2 toolchain
i have an unsolvable problem about ble on a nrf52840 based project with imu, i2s strip led, buttons, spi speaker...
i have a classic...
Hello,
We are looking at using the DTM sample firmware for BLE tuning in a form-factor version of our product. Unfortunately, the only GPIO pins we have exposed are SWDIO...
I am using the nRF7002DK development board, which features an nRF5340 as the Host MCU for the nRF7002 chip. I am testing the " Wi-Fi TWT Sample " sample project, which allows...
I have designed a PCB using the nRF52840 microcontroller and the MAX30001g ECG sensor. The sensor requires a 32.768 kHz clock signal via its FCLK pin, as shown in the attached...
I believe I have discovered a bug in the SLM firmware. I am using SDK v2.6.1.
When running the nRF9160 in MQTT datamode, we are encountering an issue where the slm_quit_string...
I have successfully setup my nRF51822 chip with Wireshark to capture BLE packets, using the 4.0.0 release of the nRF Sniffer software (extcap folder). However, the capture...
Hi,
I am currently using nRF Connect SDK v2.5.3 and want to update to a newer version, because I want to create a board definition and I want to do it in HWMv2.
Even though...
Hi! Recently, I tried putting my nrf9160dk into SYSTEM OFF mode. The code instantly puts it into SYSTEM OFF mode and waits for a gpio interrupt. The problem however is that...
nrf5340+nrf7002 running Zephyr with NCS v2.6.x.
When trying to connect to a wifi AP with incorrect credentials, I have several issues:
1/ the result of the (failed) connect...
Hello, After doing several things on my Ubuntu 24 host (I don't what might cause problem): -> Updating java OpenJDK to 17 -> running apt update & upgrade -> modifying my script...
I am encountering warnings while attempting to send Bluetooth notifications in my Zephyr-based project. The warnings are preventing successful notification of ECG data. Below...
HI ALL,
I am using v2.8.0, NRF54L15,and peripheral_uart demo has not made any modifications except for adding the following content. The test shows that the OTA upgrade...
1.test code
the code run separately on ble-softdevice and only timer demo .test code as follow:
2. test data
test result as follows：
picture A,show timer2 timing...
