Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi everyone,
I am using the custom nRF52840 module provided by Raytac. I integrated into my evaluation board and I flash it using SWD and JLink debugger. My problem is that...
I have DFU code base working. It consists of a thin layer of our code, and majority is from Bootloader component from SDK v17.
I started with DFU OTA, and then incorporated...
Hello,
I am trying to reproduce the Mesh Light Switch demo at home now, with my own dev equipment and have hit some problems I did not expect -
Problem:
nRF52840 Dongle...
I have developed an app for the nrf51822, using the nrf51-dk with SDK12.3, together with DFU functionality.
After having solved many issues to get to this point with the...
Hello, I'm using nrf52832 with SDK 15.0 and softdeveice 6.0.0.
I need to handle interrupts with different priorities on two different I/O pins. How is the correct configuration...
Hello, I'quiet new in Zephyr.
So tell me if I'm wrong.
I would like to test driver mcp23s17 present on zephyr.
I've add in .overlay file
And now I want to initialize...
Hi all,
I'm programming nRF52833 with SDK17.
I want to use only one channel (for example 37) to broadcast advertising during advertise interval and also one channel of...
My team was looking to transfer a 20-byte value (or 'message') between a mesh client and server, what is the best way to achieve this? I have practiced with the light_switch...
Hi,
I am currently developing an application for the NRF52840 using a custom pcb powered through the VDDH pin using a 4.2v lithium ion battery. Part of my application requires...
Hi,
I am trying to following the instructions at: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_user_guides_java_coaps...
I have configured the dev kit by cutting the SB9 bridge. I am powering the device from the J2 USB port on the DK. I have not bridged SB12 or SB11 as I am powering the device...
Hello all,
I am experiencing a ~5uA oscillation (between 5uA and 10uA) in sleep mode, DC/DC converter enabled, no RAM retention. The total current is of the entire system...
i am working with jlink segger edu, in a custom board, it dont have swd TX, RX pins connected, only jtag pins. I Need to see if my gps conected throw uart is working or not...
I configured the pca63519-sr3_nrf52832_shield to fit on my board (actually disabled all peripherals, only the bluetooth protocol part), but found that the modified code could...
