Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
I would like help in understanding the limitations of the NVRAM. The documentation for the nRF52840 and the nRF52832 are different. This is what the nRF52840 reads:
Do...
Hello all,
I am new to BLE mesh programming. I want to develop a multiple sensor client-server model where sensor data (eg. temperature values) from multiples nodes in a...
Setup:
- MESH SDK 4.1.0
- nrf52832.
Consider the following scenario:
- 3 nodes (A/B/C) are provisioned on the same network.
- I'm using a custom model with reliable...
Hi Team,
nRF52840 boards are getting fail continuously not able detect by Host computer.And the boards are no more useful and all boards are brand new only One day we have...
Hi,
I am trying to enable Bootstrap support.
Therefore I set "CONFIG_LWM2M_RD_CLIENT_SUPPORT_BOOTSTRAP=y" in prj.conf.
I also set "CONFIG_APP_LWM2M_SERVER" and the port...
I have built boot-loader hex file from SDK 12.1.0 secure DFU project, without any changes except for public_key.c file.
I am referring to steps mentioned under
Combine...
Dear all,
Hi, I'm Eric.
I m studying spi communication used nRF52832 base on SDK 14.2/example/spi.
That examsignal is below picture 1.
But I want to delay between...
Hi--
I noticed something rather peculiar on the built hex from segger that is programmed onto my nrf52832 chip (firmware image).
The hex looked as expected, until i got...
My ble_peripheral is bonded to ble_central, How do I upgrade at this time ? If you still use the mobile phone APP to upgrade, you need to erase the binding information, and...
Hello,
I encountered a problem when installing nRF_connect on a new computer. As shown in the picture, the attribute "middleware" of null could not be read. Opening all...
I am using as template the MQTT sample app from NRF Connect 1.3.0, for which I want to create my own application modules, I have added the .c files to src, but I am having...
Hello,
We are using the Serial port library with two UARTEs. It defines two instances of the serial port interface: one for receiving data, and one for sending data. After...
Subject pretty much explains the problem. One can just get power from a USB interface, but if I plug our nRF52840 into such an interface, it does not appear to boot into its...
I am trying to use serialization to connect an STM32F4 to an ISP1705. My goal is too connect to other BLE devices and read some measurements. I have tried a few of the examples...
I'm using an example project of the secure serial bootloader (pca10056_uart_debug) and changed some configuration for my custom board. I added RTT debugging and changed uart...
