Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I'm trying to send and receive data to DATA interface that contains IN and OUT bulk endpoint (usbd_cdc_acm example). I'm using libusb on the PC side. It seems like I...
Hello,
I use PPK to measure the power consumption.
but I always get : Failed to start the PPK.
I have measured it last week and it is work.
and this is nrf connect...
Hi Team,
i am working on nrf51822 customized board, the SDK version is 12.3.0 (soft-device is s130 ) and Developing environment in keil 5.26 (on windows).
i am trying...
github.com/.../nrf52-ble-multi-link-multi-role I modified the code to access the environmental values and motion value
but if one thingy access one value such as temperature...
I develop an Android app which connects to a Nordic chip, and I cannot get the Android app to stop advertising once it connects to the central from the SDK multi link project...
Hi,
On the custom board I'm working on an nRF52832 uses the SPIS port with no CS signal (because of the HW connection with the master side of the bus). Since the internal...
Hi, i am trying to disable a signle GPIOTE channel via the INTENCLR. Here is a simple test case:
void gpiote_set_clr_test(void) { NRF_GPIOTE->INTENSET |= ((1<<3) | (1<<1...
Hello ,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hello!
I have been developing a BLE application on nRF52DK and used the ACN52832 as a module for a custom board for experimenting with BLE. I ordered a custom PCB from...
I am just starting using a Thingy:52 and want to use it with a C# UWP app. So far I have been able to retrieve the service and characteristics UUID's without issue but I am...
SDK 15.0.0 nrf52810 Example: Eddystone Beconing mode - ble_app_eddystone SEGGER Embedded Studio for ARM v4.12
I am using ble_app_eddystone example to advertise data in eddystone...
My development enviorment: SDK 15.0.0 nrf52810 Example: examples\ble_peripheral\ble_app_template\pca10040 e SES IDE
I am running above mentioned example without any changes...
Hi
I have a requirement to be able to re-start advertising with new parameters when told to do so over a Slave SPI interface. From other posts, it appears that there is...
