We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
We are releasing a firmware update which adds an additional bluetooth profile. Since we do not want or can retest the entire stack, we use a Previously Qualified Design (51744...
I'm using NRF51822 with soft device version 6.0.
I'm trying to create an event which should be triggered every 24 Hours. In the current implementation in our code base...
I saw the demo of nRF52832 connected 20 peripheral devices and control the light in the peripheral.I would like to know the more deatil of the whole operation in chip/SD....
I've searched and the majority of answers seem to be years old.
I have an existing app_timer event handler that works perfectly, blinking LEDs.
I will soon have another...
Hi! I'm using two RedBear Nano v2 and I'm trying to read a long characteristic from one of the two devices. As I read in other posts in the forum, I need to invoke the read...
If I'm not mistaken, both S110 and S130 support OTA DFU right?
I understand that nordic semi most likely recommend S130 over S110, but please understand that
my current...
I have previously developed on the nRF24LU1+. This device would have a CHIPID in the InfoPage, This ID would have guaranteed it does not violate the requirements for ESB addresses...
Hi, im using NRF52832 whit SDK 12.3.0, when i compile this error appear, "undefined reference to `nrf_drv_spi_init", i included the "nrf_drv_spi.h" file.
also try to include...
Hi everyone,
I'm working with nrf52832 and i'm trying to send data over BLE for communicate with a mobile app. I saw that we could pass data with the function ble_nus_string_send...
Minor nitpick:
The PS_v1.0 datasheet says that "see the Reference Layout section on the Downloads tab for nRF52840 on..."
There is no Reference Layout section on the Downloads...
I am working on a BLE bootloader using SDK 14.2.0 on an NRF52832 device, using softdevice version 5.0.0. I am able to get the bootloader up and running, and I am able to see...
Pre Conditions:
1. As soon as the connection is established the App start a timer to disconnect the link using sd_ble_gap_disconnect
2. The app timer has the same timeout...
Hello,
I'm searching the possibilities of Thread mesh network. And I want to minimize the size of border router as small as possible. Have you considered to port the border...
Hi,
I'm having trouble writing to a characteristic when operating as a central. I'm sure it is just a lack of understanding on my part but neither the SDK documentation...
