I have an external GPS module connected to an nrf9151dk over UART. The module is correctly powered, and sending messages over its tx pin, which has been confirmed by attaching...
I´m trying to change the installation path of the Nordic Power Profiler as I´m running out of space.
I have about 9GB left, but when trying to open a captured file, Power...
Hi Nordic team,
I’m working on a custom LoRa interface using the Thingy:91X, and I’d like to know whether the Qwiic connector pins (P0.03 – SDA, and P0.04 – SCL) can be...
Hello,
I would like to measure the current consumption of my nRF9161 and compare the result with a standard measurement. While searching in your documentation, I found this...
Hello,
Does the nrf_oberon library support the nRF54L series parts? In the technical documentation, it appears that M33 parts are supported: https://docs.nordicsemi.com...
I'm having trouble enabling BLE DFU on my firmware for the nRF52833. I'm following the steps from the Dev Academy course - FOTA over Bluetooth Low Energy . After adding the...
Hi,
I have a board with a real time clock IC which is kept alive during power downs. I want the Nordic nrf52840 to read the time from the real time clock and then use this...
Is it possible to program the Atmel SAM D20E chip (based on an ARM-M0 cortex processor) externally using the P19 debug out header on the nRF51-DK?
Thanks.
I am trying to understand the Passkey LESC pairing on S140 soft device using the latest SDK 14.0.2.
The message sequence charts has a block "App starts DHKey calculation...
Hi developer, sorry to interrupt and ask. How to use an ultrasonic sensor with nRF52? Since I search a code for nRF52 are not exist and see ultrasonic sensor can connect with...
I modified TWI_SENSOR_PCA10040 example from 14.10 SDK to run on my NRF52832 device, and it reads from the device address perfectly. However when I wrap reading inside a FreeRTOS...
Hello ,
What is the preferable way to flash code into NRF52832 IC during mass production? Flashing the code into custom IC with NRF52-DK in time consuming process.
And...
Hi,
All of a sudden (isn't it always the case :) the JLink debugger fails to flash the app code to the dev kit (PCA100028)
The Project's softdevice is flashing well without...
I have configured 3 differential ADC channels
to sample with timer/PPI/DMA buffer.
When I turned everything off, I couldn't get below
20uA current (with only LFCLK running...
2017-12-07 22_28_04-D__Users_Eyal_myWorkspaces_KeilMDK_ble_peripheral_ble_app_hrs_rtx_pca10028_s130_.png
Hi,
I've developed a BLE Central app based on the SDK HRS collector...
Hello,
I am using NRF52 TWI master to read data from my sensor, I have read the twi_sensor example but it doesn't make use of nrf_drv_twi_xfer() .
My question is quite...
Dear nordic employee
1、when I use the spim to send 1 byte address to read it's value(4 bytes)，like this：
nrf_drv_spi_ transfer(&spi,headerBuffer,(uint8_t)headerLength...
Hi!
I use this debug on another examples fine. But want to enable this debug in a my project. In a config.h file RTT debug enabled. But doesn't work debug. I remarked that...
Hello All,
Please check above image, showing antenna layout of my custom board.
I am receiving error frames at ~40ft distance on sniffer.
Please check whether antenna...
When creating a custom bootloader for buttonless DFU, it is surprising to see that nrf_dfu.c not compile without defining button related function.
The warning
nRF5_SDK_14...
After succesfull compile, installation and run of my first application , I cannot see anymore the nRF52 DK board from windows.
The application keep flashing the led but no...
I wanted to share the most reliable and efficient method I found to collect and store my log outputs through segger RTT, which also allows using the excellent Log Viewer Log4View...
