Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
HI People,
I use nrf51822 CEAAE00 (0x0079) chip which has 256 kB FLASH, 16kB RAM. I faced a problem when compiling the bootloader for it. The solution was I am using a...
I am trying to build a custom board, based loosely on the nrf51-DK (which I have been testing). I haven't ever directly programmed a chip before (always used interface MCUs...
if I send only the advertisement, it sees that data
Is there something in the IOS that prevents seeing manufacturers data in both the advertisement and response packet?
I found the Ble Serialization here and the example sourcecode within the sdk sources.
The sources are for using S110 softdevice.
Does Ble Serialization also working...
Hi, I'm trying to get my nRF51 code (which works on my dev machine) to tun on the test server (both Win7). Am using MasterEmulator 2.1.10.8567
The dongle itself is happy...
Hello I am new to this platform, can anybody tell me how to write the value on serial in NRF51822
and what is the command through which i can write the value on serial. getch...
My application uses ble_radio_notification_init. Every time I switch from my application to the DFU bootloader it drops the connection about 10 seconds after starting the...
Trying to follow
devzone.nordicsemi.com/.../
but whatever I do, I am unable to make Eclipse discover the include paths or the source file paths from the makefile. I've...
Hi,
My Nordic kit just stopped detecting from last two days.
I have also check this in other PC also.
It detects some times some times not.
I am using Windows 8.
I...
Hi all,
I would like to know if it is possible to use the uart before the actual bootloader runs... I need to communicate with the master uploading the firmware before...
Hi All,
I need to implement a kinda a mesh network of Nordic device nodes placed nearby to act as a relay, for that I have a use case where following requirement.
...
I'm porting a nrf51 project to nrf52. I'm using softdevice s132 1.0.0.3 alpha. When compiling I get a lot of L6406E errors and a L6407E error. Do you know what's causing this...
hi,
I should how to transplant the official DMP mpu6050 library to nrf51822 above?I don't know how to transplant it and could you tell me how to transplant it?
I have combined to programs Ble_uart and Spi_Master into one. However, after uploading the file the GPIOs do not work (No clock is generated). Meanwhile when I erase the softdevice...
