I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am using the NRF51822-CEAA flip chip package for my custom board.
Because this package has an optical vulnerability from the sides, could you please advise how...
Hi developers,
I recently had a problem with nRF51822 and radio interrupts.
My situatios is quite clear but I cannot resolve the problem. I hope You will help me.
Description...
hi,everyone.
because of careless,i enabled pin reset in debug mode by set bit 0 in RESET register in my software,and i downloaded the hex file to a 51822.now,because of resetting...
Hi all
According nRF51822 Product Specification , GPIO pin can config to SPI interface. Means if I set a specific GOP pin range to SPI and connect these pins with...
I am successfully sending data from the PCA10001 Evaluation Kit to the Master Control Panel. But I cannot find any information about initiating and sending data from the MCP...
Hi,
Here i am attaching my text file. in my case timer api is working
but button event handler is not calling.
Kindly tell me , what is my fault.
Regards
Balaji...
I want to store a block of data in nRF51x22. I tried the following:
void HalStoreNVMBlock(uint32_t size, uint8_t* pBuf)
{
nrf_nvmc_page_erase(NRF_UICR_BASE);
nrf_nvmc_write_bytes...
I'm using the TWI module. Where can I set whether the DSA SCL pins have the internal pull-up enabled or disabled? I can't even find where to see if they are enabled at all...
Hi guys,
I am having a breakout board made and would like to know what are the programmers out there which I can buy which will help me program the board. The J-Link is...
Hi,
I'm designing a custom board equipped with nrf51822 and is not clear for me how the flashing part works; I bought nrf6700 and pca10005 as reference design and now i need...
I am coming across a strange issue with a nRF24L01P running enhanced shockburst. I have 1 PRX and a few PTXs communicating in a star network. The type of PTX determines which...
Here i am attaching text file in which my application not able to call interrupt handler.
Kindly tell me what will be issue.
Regards
Balaji
rtc1_app_timer.txt
I'm trying to figure where the BLE bottlenecks are to figure if I should use BLE or maybe Gazell for my product. I've just started to use the BLE stack, so I guess that there...
hi,
i am working with the nRF51822 development kit and trying to load the sample programs given by the nordic guys, the samples without using BLE is working properly but...
