Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
i have used "BLE_GAP_PHY_AUTO" in scanner code
actually it should scan "phy coded" and "non phy coded" aid values .
but in my case getting i was getting both "phy coded...
I have a project to use NRF52810 to connect the App. When testing it, I found that when it was successfully connected to the NRF Connect tool, it would automatically disconnect...
Hi, Dev Zone.
thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
1st_question <- this is my first question links
main problem...
I'm using
SDK : nRF5_SDK_17.0.2
Example Project : ble_app_uart
Soft device :S113
The initial project builds successfully.
My project has requirements for tow...
development tool : Segger Embedded Studio
SDK:nRF5_SDK_17.0.2_d674dde
it always takes long time to build project
build log:
Building ‘blinky_pca10056’ from solution...
Hello all,
I am developing an application from the ble_cgms example on the nrf5_sdk 17 using the Softdevice S132.
I have implemented a gpiote interrupt whenever the state...
Hello,
I just received nRF9160DK(PCA10090, 0.8.3)
I followed nRF9160_DK_Getting_Started_Guide doc.
But, I hare some issue to activate iBasis Sim card.
It keeps...
Hello, I am using the latest version of pc-ble-driver combined with a pca10040 and I am attempting to write large data packets (200 bytes) to a peripheral. I compiled the...
Hi,
I have tested FOTA code in nRF52840 DK and it works perfect but i have custom board build with nrf52840 when i implement the code it doesn't get start
custom board...
I don't have time to learn the massive API for nRF52840 so I am hoping someone can provide a small
snippet of code (and instructions to put on the dongle) to do the following...
Hello
While converting from nRF52832 to nRF52810, we found a problem that the SEGGER compiler returns with the message
section '.init' will not fit in region 'UNPLACED_SECTIONS...
Bluetooth didn't have a standard for transmitting audio using LE until LE Audio was released. And many manufacturers which produced BLE remote controls used Voice Over HID...
In my project, nrf9160 has to send and receive data from the I2C bus from a chip. Everything works fine but unfortunately I have to query the chip by sending a single byte...
Hi,
I'm using nRF52840 DK to construct and test a wireless data transmission system.
The problem is that I need to detect a 2M Hz clock's rising edge using nRF and...
Dear Community,
we are looking into an application where the Gateway (RX) uses the nRF5340 + antenna array and the clients (TX) the nRF52840. The clients are on the market...
