Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Newbie here simply trying to run some example projects from the SDK.
Setup:
Segger Embedded Studio 5.10b
Tried example projects in both SDK v17 and v16
nRF52 DK...
We have a working app for SDK 16 and freeRTOS. We wanted to update to SDK 17.0.2 but after upgrading the app hangs up at the first vTaskDelay(). We use configUSE_TICKLESS_IDLE...
Hello, I am a newbie in this forum and I'm not very familiar with app development in general, however I am in the situation in which I have to develop an app to acquire ANT...
Hello Nordic Team,
I am having issues with the HCI UART firmware for the nRF52840 on the Thingy91. I have been using the HCI UART firmware from nRF Connect SDK 1.0.0 for...
Hi, I am working on a project to send commands from mobile to device and vice versa. I am using nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_template . I have made...
Hello,
I am using : SDK 17.0.2 and S132_7.2.0 with nrf52832 DK
in my BLE application, the FDS has 2 behaviors :
1) When the softdevice is enabled : fds_write returns...
Hello,
I´m searching some information about the NB-IoT protocol stack and the overhead which is send with every message.
I nearly searched the whole net but didn't find...
Hi,
It has been stated that nRF9160 doesn't support RLC UNACK, which we have also observed with nRF9160-DK in signalling mode against radio communication tester. Are there...
Hi,
I have a setup where mobile device(central) connect to nrf51dk (peripheral) and exchange data for a time. I want to detect unplanned disconnection of mobile device in...
Hi all, I try read DEVICEID in non-secure application but always return "BUS FAULT", I tried too enable NRF_FICR register in "spm.c" but the error persist!
I try
NRF_FICR_S...
Good morning Nordic,
I am trying to configure the I2C pins for our board (using nRF5340-QKAA SoC) but I cannot find the pin numbers for I2C_SDA and I2C_SCL.
All I could...
Hi all,
We are using the BMD-340 from uBlox, which runs the nRF52840 SoC.
On this BLE Peripheral, we are running the ble peripheral demo project ble_app_uart (pca10056...
Hi,
I am trying to disconnect an Android smartphone from the nRF52840. After trying for some time we found out that the BLE stack of Android does not reliably closes a Bluetooth...
hi..folks
wish you happiee new year
i am using nrf52832 whille i tried to pair my device with my android , i am getting an error message " pairing rejected by nordic_uart...
Hi,
According to below thread, the advertising interval has a random 0 - 10 msec delta, so if the adv interval is 20 mses, if run it for long enough, will the result be...
