Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Hello,
I have NRF5230 DK board and I have powered the board with external battery. Solder bridge SB12 is shorted and I have cut the jumper SB29 and disabled power for Interface...
I am trying to connect nrf52832 ble module to esp32/esp8266 application mcu connected with SPI interface.
I use ble_central/ble_app_hrs_c application, but found that the...
Hi Sir,
we use 52832 ESB , one PTX and two PRX. (PRX_A and PRX_B)
A and B have same base_addr_0 and base_addr_1 .
diffrent addr_prefix
PTX send package to A and wait...
I am trouble with adding DFU function to BLE_UART on nRF52832. I have just followed those step in this link Adding DFU to your App . But when i compile and fash to my device...
Hi all, My company is doing a proyect with BLE. We use nRF51822 with the softdevice s130. I am preparing the FCC and CE certification. Our tester asked us to prepare 2 samples...
hi, nordic team:
Now I am using the nRF5 AirFuel SDK version 2.2.0 to develop the PTU and successfully use the serial to do the dfu function.
I used nrfutil for DFU, but...
Hello, I trying to debug with GDB server Because of this .
I open the GDB server like this
go to build directory and write client cmds below
output is $4 = {<error...
SDK12.30 supports S132 V3.0. Is there any other version SDK supporting S132 v3.1?
Any problem for firmware built with S132 V3.0 and running on module with S132 v3.1?
Hello,
I've disabled the buttons in light_switch example for the client DK. I'm using GPIOs for input and I want to enable BSP_BUTTON_3 to reset mesh network configurations...
After switching to SDK 15 from SDK 14, stopped working correctly transmission of HID Report Descriptor over USB, what in case leads to incorrect device enumeration.
Now...
I'm developing a database with FDS that stores application-level data that must be able to be matched to bond data. After looking at the files for Peer Manager, ID Manager...
Hi All,
What is the recommended way to choose FIFO and buffer sizes for the nrf_serial module? I mean the optimal values for the following constants:
SERIAL_FIFO_TX_SIZE...
Hi,
the pull-up resistance Rpu of GPIO pins as stated in Product Specification v3.1 in Table 62 is supposed to be 13 kOhm (typ). Since we measured a different value on pin...
I started development with the S132 (SDK 15.0.0) peripheral example "blinky". After some modification, it handles all necessary communication with my phone flawlessly. Now...
I'm attempting to use the USB MSC example (from nRF5 SDK v15.0.0) with external flash chip replaced with Winbond W25Q128FV and I see the following logs:
[00:00:00.000,000...
