I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi all,
maybe a dumb question, but here to listen any advice. I am using nus to receive data from a phone, packets are in chuncks of 256 bytes, which is the "most used"...
When I flash the card and run it, I encounter the screenshot I shared in the attachment. The error "Modem has crashed, reason 0xfff, PC:0x0" occurs. Can't I send messages...
Hi.
We are using nRF52833 (on BL653 module) where UART0 and UART1 are used for communication purposes (one with STM MUC and the other with quectel modem). Current solution...
I'm working on a personal project and have designed and printed a small prototype board containing an nrf52810, external antenna, couple of crystals, and a ws2812b onboard...
Hi,
We are developing a mesh network. Our requirement is the one device can connect to three other devices. Using one connection as a peripheral and up to two connections...
I am working on iOS pairing and bonding and connection and disconnection through UART.I am facing issue where pairing is initiated after that the device is getting automatically...
Hi,
We are experimenting with Distance Measurement feature a we observed 2 issues.
HW: Custom HW with: CR2032 coin cell -> joulescope -> 40 uF capacity in ceramic caps...
Hi all ,
I 'm experiencing issues with MQTT client connection on an nRF9160 board via LTE -M .
Some context : I 'm trying to connect to a MQTT broker via LTE -M (actually...
Hi , I am wondering if anyone with SPI expertise can answer this Q , I 'm using an nRF52840 with spi_transceive_dt()
In my devicetree I've configured SPIM on SPI3 to talk...
Hello,
I used the default sample from the nRF SDK with the same prj.conf file. I can flash it to the board successfully, but I'm seeing an error in the terminal. My toolchain...
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_freertos
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_rtc_freertos
I burned these...
I am using nRF52840 to interface my MPU6050 sensor via I2C , I build and flashed the program and there were no problem. But I can't see any clock signal on the default I2C...
I'm trying to build the zephyr/samples/net/sockets/http_client. I selected thingy91_nrf9160_ns for the board config and it builds and works fine. However when I enable
...
In my project, need an external sram with SPI interface to increase the sram volume.
I'm not sure if I can do it，please give an exsample in C language and some tips.
An...
