Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello Nordic
We're developing an application where the second firmware partition is saved in external storage, which we would like to be accessible by both MCUboot and the...
I will calculate the capacitance of the external capacitors for the 32 MHz oscillator circuit, but the values of the Cpin for XC1 and XC2 are not specified in the the datasheet...
When I follow the use_gpio_pin_directly manual I get a compilation error:
```
/home/gal/dev/ism330bx_driver_contribution/zephyr/include/zephyr/devicetree.h:196:36: error...
Hello,
I'm tinkering (motion detection mostly) with a Thingy:91 unit (I don't have a DK board), and in general it works fine reporting sensory data to AWS IoT Core.
Last...
We’re developing a medical device under IEC 62304 and plan to use nRF Connect SDK. Does Nordic offer any documentation or process descriptions to support IEC 62304 compliance...
Dear Customer Support,
We are gathering the list of supported AT commands support for the nRF9151
Also experimenting available AT commands using the nRF9151DK
So far...
I’m trying to build and flash a BLE Mesh DFU application for the nRF5340 DK board, but it isn’t working. I selected the nrf5340dk_nrf5340_cpuapp build target only. Could you...
Hello,
I’m developing a composite USB device on nRF5340 (NCS v2.6.0) that exposes USB CDC + MIDI + Audio. When using the USB Audio interface, volume control works correctly...
I am trying to reset an nRF52840DK - it is visible within the nRF Connect SDK in Visual studio code but gives a timeout message:
[14:27:11] nrfutil-device reset --serial...
Hi everyone,
I’m currently working on a small, battery-powered tracking device based on the Nordic nRF9151 SiP . The goal is to create a compact and energy-efficient product...
I am unable to program the Thingy:91 using nRF Connect for Desktop → Cellular Monitor application , as described in the following link:
https://academy.nordicsemi.com/courses...
Hi,
what is the recommended way on the nRF91x1 to clear the Forbidden PLMN list?
Devices may get denied on networks repeatedly, filling up the FPLMN list. To ensure the...
Hi, we are still struggling with nrf9161 behavior and trying to mitigate data sending dropouts ( and ).
Here is one partial issue: we are currently using UDP and flushing...
using west update i just update the old version 3.0.2 to 3.1.1 and after take blinky code and build then i have got below error,also using the vs code i doenload the NCS v3...
Hello, While designing the hardware circuit for the CAAA WLCSP with internal LDO regulator setup on the nrf52810, I removed the 32.768kHz crystal oscillator and retained only...
