i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hey all,
I want to try the Asset Tracker v2 (NCS v1.6.0) Application in AWS, so I followed this guide .
When I try to create the CA certificates and register them in AWS...
Hi,
I'm trying to build the smp_svr example for Thingy:52 but build fails when linking.
I can build for the nrf52dk_nrf52832 which uses the same chip. What can i do to...
Dear Nordic Team,
We have a running product that is using 32KHZ quartz from MicroCrystal : https://www.microcrystal.com/fileadmin/Media/Products/32kHz/Datasheet/CM7V-T1A...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. I also have a run-time radio test mode which...
Hi, I have installed the most recent version of nRF toolchain manager for windows (V0.9.2). nRF SDK V1.6.0 was released a couple of days ago but it is (not yet?) in the list...
I am new to BLE.
My question is similar to the one below.
https://devzone.nordicsemi.com/f/nordic-q-a/22596/nrf51822-central-connect-and-communicate-with-2-peripherals...
I am using the nfc_writable_ndef_msg example in the SDK to write from my phone to the board using NFC. I get it working successfully however, I am also trying to add code...
Hello, I'm using nRF52833, pca10100, s140.
I'm going to write a code using the external 32.768khz crystal to determine if the port is high/low every 0.5 seconds through...
During the release, we got 2 files with firmware, with and without confirmed in the name.
I want to upgrade my device with the nRF Connect application and confirmed firmware...
Hi all：
We update SDK from 11.0.0 Version to 17.0.2, the hardware is same, but from 17.0.2 package, we run DTM in single channel mode ,data lost is 40%. DTM from 11.0.0...
I have an issue with creating a Bluetooth mesh gateway. It would be better to use nRF Connect SDK for me, but nRF5 for Mesh is also fine. As I've found among answers, not...
Hello guys,
I try to implement a pdm sensor on the nrf 52 dk which sends the audio data to a central device.
My setup is two nrf 52 dk one acting with the modified ble...
