Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
Apologies if this is answered in some other thread but we cannot find the precise answers we are looking for and are striving for some quick clarifications. We are planning...
The ble-sniffer_win_1.2_user_guide, Figure 4. Wireshark Interface, Packet Bytes window shows a 00 byte at location 0010, which corresponds to the "preamble" of the "Air Interface...
Hi
I want to declare 2 spi instances with only cs pin different.
The reason for dividing the two is because the modes are different.
The one declared above is executed...
I have used nRF5 SDK ver.16 for BLE HID digtiger.
I want to set up some feature value to HID report . Such as Contact count maximum.
I have followed keyboard example,...
I turned off the serial i n prj.conf of the mqtt_simple routine.
<prj.conf>
<nrf9160dk_nrf9160ns.overlay>
The idle current was measured at 500UA. This means that...
Hello Engineers,
We are trying to set the correct configuration between nrf9160 and nrf52840 for using the uart_pipe library. However we are still unable to communicate...
We have a Nordic development under way and I have run into a snag.
Neither of my dk board types (9160 or 52840) are recognized by jlink , no jlink drive etc….
I have personally...
So the interrupt on the nRF2401+ seems to be working inconsistently. I get interrupts sometimes and sometimes I don't.
For a context: I'm transmitting a sensor data only...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
Hi all,
I am using the nRF51822 and attach you can find the . .
I have noted that the current consumption is too hight for my scope (about 1.7mA). My idea is to 'reduce...
I tried: - changing USB cables and ports (no any improvement)
- instructions from this link devzone.nordicsemi.com/.../nrf52-dk-does-not-show-as-a-removeable-drive-in-windows...
Hi there,
My question is similar to https://devzone.nordicsemi.com/f/nordic-q-a/39447/central-role-in-a-mesh-proxy-node , but perhaps slightly different in that my existing...
DFU Trigger Library (USB) is indicated that only for nRF52840 SoC. For other SoCs, can I use it after some modification of the library easily? What's the limits?
Hi !
I am on a firmware project for a nrf52832. I am using SES on Windows.
There seem to be a problem when combining buttonless DFU and NUS. When I do the services_init...
Dear devzone community,
I am currently in the process of migrating my MBED code to NRF5 SDK. My MBED code is functional and it works fine, you can find the code below: ...
