I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hello,
SDK: 15.3.0
nRF52840-DK
s140
I have taken the flash_fds_s140_pca10056 example and modified it for our own use. I would like to store versioning information...
Hi Team,
I am working on nrf52840, for openthread application
I flashed cli code built with USB=1 (enables Nrf USB J3), DIAGNOSTIC=1 (enabling factory diagnostics) option...
Hi !
I use SDK:15.3.0 ,Mesh v3.2.0 and have tried official dfu example which is ok.However, When after I enable marco "MESH_FEATURE_PB_GATT_ENABLED=1 MESH_FEATURE_GATT_PROXY_ENABLED...
Hi,
i have designed my custom hardware using BMD-301
i'm able to upload code in bmd-301 using segger embedded studio.
after code uploaded device is not broadcasting...
Hi team, I faced the following problem: there is a custom board with nRF52810 on it, UART is used on this board.
I set up Debug configuration and UART is working OK, but...
Hi,
I am working on a project where I need to send and receive ASCII strings from my Central Device to the Peripheral Device. Before the communication starts there should...
Hi, we have an nRF9160DK (0.8.3) and it does not connect to the nrfcloud.
We have updated to the latest firmware 1.0.0
We only have nb-iot here so we didn't use the iBasis...
Hi Guys
I need your advice. I have a customer that is currently in production with the NRF52840 . They now require direction finding but need a Nordic Evaluation kit to...
Hello,
I am new to Nordic platform, previously i had worked on TI controller.
I have three questions to ask:
1) My firmware consists of four services, each service...
hi,
I am using nRF52832 with KEIL. I want to use version6.0.0 softdevice, but I can't select from KEIL runtime library.
Also, the version that can be downloaded from...
I am trying to change after 10 seconds into non-connectable mode. I am using the below code for initializing:
I want to change mode into non-connectable using this type...
When I use dfu_nrf52832_xxAA_s132_6.1.1.hex, it works all devices updated with blink code as described in dfu_quick_start.md But without any provisioning Process, why? And...
Firstly , I have 2 phone. Phone A is huwawei using android 7 and Phone B xiaomi pocophone using android 9.
Phone A already success connect using UART. But I want to try...
