We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Good morning, if I wanted to develop a board with the VM3011 device, where can I find it? It seems impossible to find it as a device in major stores, and I can't even find...
Hello,
I would like to develop a temperature logger which Starts to log temperatures between certain limits
The data is stored until the device has connectivity to the...
Hello,
I know this issue has been discussed extensively in different posts, and I believe I read all of them, but still I can't get it working.
I'm trying to drive...
Hi,
I'm trying to run the i2s output sample from NRF Connect SDK 2.7.0 on the nrf52840 DK, and I'm only getting the clock signal from P1.15, and no signal from any of the...
I'm just a bit fuzzy on how all of the bootloader stuff comes together.
Our application is small (100K-ish), so a dual-bank strategy seems appropriate.
It uses a proprietary...
Hi.
Could you please tell me how to trigger an interrupt when changing the USBREGSTATUS register?
I can monitor the state of this register in polling mode, but I don't...
We used two different packages of 833 and assembled two batches of PCBs. The first batch used the aQFN package, and the radio can operate normally. The second batch used the...
Hi,
We are using nrf Connect SDK v2.0.2 with the hci_rpmsg app programmed into the network core. We have a second radio test DTM application programmed into the network...
Hi, I have used nrf5_SDK//examples/ble_peripheral/ble_app_hids_keyboard & ble_app_hids_mouse both examples with my nrf52840-DK this device is visible in my mobile and laptop...
Hi,
I have a custom nRF9160 board. ADXL362 & MX25R64 share the same SPI bus. I'm trying to validate it individually and looks like there is no communication between both...
Hi.
Board : nRF52840 DK
SDK : NCS 2.0.0 (zephyr) or SDK 17.1.0
I test qdec example.
if I set sampleper value 256us/128us, NRF_QDEC_EVENT_SAMPLERDY Event is not raised...
I am recently trying to get up and running with the nrf9160-DK and have been unable to flash the board successfully even with the Quick start (v0.2.6) app in nrf Connect....
I wanted to try getting all 3 outputs on my nRF5340DK. I tried following the instructions here - https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/security/tfm.html#manual_connection_to_virtual_com_ports_on_the_nrf5340_dk...
Hi,
We've developed a custom PCB featuring the nRF52840 Core Chip, but we're encountering significant challenges with antenna performance, resulting in poor range during...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
