I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
hi Nordic support team,
I cannot re-flash firmware for nrf52840 after ram off is implemented.
I recheck with other chip like nrf52833, it have the same result: \althrough...
I understand, it is possible to add variables to a section of ram, that will not be initialized (zeroed) at boot (see for example: https://github.com/nrfconnect/sdk-zephyr...
Hello,
I want to create my own board from the nrf52840. I am planning to copy the schematics given only taking into account what I need. I went through the schematics and...
Hello,
I am using the nRF51822 with SDK v9.0.0, SoftDevice S110, and the DFU bootloader v8.1.0.
For certain reasons, I want to reserve one page of the 'app data' for shared...
Hi Support Team
If a center role and a peripheral role in one nRF52840 at the same time，can the center role use code PHY and the peripheral role use 1M PHY？Many thanks.
Hi,
I need to read the data from an acceleration sensor. I tried with a custom program of mine to simulate some data, but it is delaying too much.
I tried reducing the...
Hi,
Iam using nRF5340 DK and nRF Connect SDK V.2.6.1.
Iam following the link
FOTA over BLE
In this one until 5th step it worked fine and while doing 6th step it is...
Hi,
I have purchased some Thingy:91 devices. They are HW version 1.6.1 but I cannot find the documentation for that on your website. It seems that the latest available is...
Hello,
I am using nrf5340 Audio DK board. In that board I have flashed a sample firmware of Unicast Gateway.
This firmware is suppose to scan the advertisement and establish...
Hi there,
I am writing code to set my BLE PHY throughput from 1M to 2M when my device establishes a connection; my code works when I connect to my nRF52840 dongle from a...
Hi ,
I'm in Nrf52840Dongle Getting the PCM data in the following way, I want to print him to the serial port and then import it through Audacity to make sure I have the...
Hi,
I'm trying to understand how I exactly can differentiate between CODED S=2 and S=8. I've experimented with the BLE fundamentals Lesson 3, Exercise 2 and set the PHY...
Hi,
I am using VS code for nordic 9160dk, and when create a new application - copy a sample and choose the Blinky sample / Asset Tracker v2 application , and build configuration...
Hi
I am using nRF52832 , SDK17, S132, reading a device ID which should be 0x67, I am reading 0x33, than 0x80 ,so it seems to be that the MISO window is getting offseted...
nRF52840 SoftDevice S140 7.3.0. nRF5_SDK_17.1.0_ddde560. IAR for ARM 9.32.1.
Central Role managing 16 connections to Peripherals together with USB communication to a PC...
