Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
I am using an nRF chip and the nRF SDK for 1st time and I think I am still at the steep part of the learning curve.
My problem is that I cannot get the log from my custom...
We are developing a device that communicates with a remote management system via tcp sockets over LTE. We are using the NRF Connect SDK 1.4.0 with modem firmware mfw_nrf9160_1...
Hello,
I want to transfer analog values via BLE to a external Device. The SAADC is initialize for 2 channels, triggered by RTC-timer and i've get the right values from both...
Hi,
I wonder if it is possible in the nrf91-device to read how much data there is left on the SIM-card.
Where is that information stored?
How does one normally get the...
We using Android Phone (OPPO A53 Android 5.1) and some custom tablets (Android 9.0), to start add custom board as BLE mesh node. But sometimes the reconnection failed even...
Working with the GPS sample.
Builds fine on 1.5.0
on 1.5.1 building with west I get
-- Application: /opt/Nordic/ncs/v1.5.1/nrf/samples/nrf9160/gps
-- Using NCS Toolchain...
I'm trying to upload image asset binary files onto a custom hw that uses the nrf52833 mcu. I use mcumgr for performing DFUs and I would like to use it to upload the binary...
I would like to enable access protection on my device, ie no debugger or flash access. Going through the docs, it looks like I’d have to do a few registers to get access protection...
Hi
I'm new to zigbee programming, but as i understand it is possible to make a zigbee mesh with routers only to decentralize to network.
I have tried to start with a...
Hi,
The most recent version of nRF Toolbox v5.0.4 for iOS cannot see or connect any of my devices (nrf52832, SDK 15.3.0, s132_6.1.1) in the NUS/UART section of the app...
I've recently update to 1.6.1.
I'm testing with SLM, only modification is using UART2 to support communication with an external mcu on another board.
HTTP client interface...
I'm currently trying to send a HTTP body payload that includes "\r\n" in the data payload. I'm getting an "OK" response before I have sent the complete payload.
The problem...
Hi,
I use the nRF52832 with SDK14 and no softdevice.
The MISO on oscilloscope is correct but value in the receive buffer is wrong (can be any value). Unfortunately...
Hello,
Sometimes we don't get a fix when seeing 6 satellites with highest 27dB and lowest 18dB signal strength. And sometimes we are able to get a fix with a GPS fix even...
Hello,
I use NRF52832 with SDK 17.0.2.
I run app timer and pwm driver independently ok.
I merged App timer with PWM Driver. But only PWM run, I can't make app timer...
