Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
Hello everyone,
I getting stocked now for 1,5 days to get the nRF-Connected SDK running
I am using macOSCatalina 10.15.7
segger 5.20
Nordic SDK Tag v1.4.0
using...
Hi Team,
I'm working on scanner and NCS/Zephyr bt_le_scan_start callback API
typedef void bt_le_scan_cb_t(const bt_addr_le_t *addr, int8_t rssi, uint8_t adv_type, struct...
Hi
I have implemented a custom DFU process, where NRF52840 sends another NRF52833 an image to program.
The NRF52833 receives the image and validates CRC, if all OK , I...
Hi,
I'm using a nrf52833 in may application.
I have 2 Identical units with bare nrf52833.
refer the unit as normal ad defective.
test a.
while flash a simple FW...
Hello ,
I am using NRF 52 DK 15.3.0 SDK and ble_free_rtos_hrs example , I want to have a feature to start and stop the advertisement ( by interrupt driven , task notify...
Hi Nordic..
currently we are going to implement serial bootloader dfu from other MCU (infineon chip).
We have create flasher from MCU to nrf52832 to do serial fw update...
Hi
I am using nrf52832 .i am trying to connect to a device using sd_ble_gap_connect but i am getting NRF_ERROR_INVALID_ADDR error.
i am modifying ble_app_cli to achieve...
Hello
I'm going to use J-link's virtual port to see the characters being printed.
I connected custom pcb to Vcc, Swdio, Swclk, Gnd pin and tx, rx pin of J-link.
And...
In our mesh application, we are trying to give all our devices the same network key. As we are planning to have in excess of 100,000 devices, the 2-byte unicast address is...
Hello,
I am developing thread network and i am building on top of mqttsn_sleepy_publisher example. But I have problem to enable RTT logging (UART not available) for thread...
Hi, We are using nRF52840 in our design. the pin p0.10 is marked as LOW-FREQUENCY I/O (up to 10Khz) according to your recommended usage. Our software is design to generate...
Hi,
I am trying to use the VL53L0x sensor with the NRF52DK. Someone has written a library but its based on c++.
(*Edited) The example provided in github works with SDK16...
