We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi,
I've got a custom board with nrf52832 mcu. I use the nRF5_SDK_16.0.0_98a08e2 with s132_nrf52_7.0.1_softdevice.hex.
Sometimes the app_error_fault_handler is called...
Hi,
I have a project based on the NUS (Nordic Uart Service) example.
I have bought a USB dongle MDBT50Q-RX manufactured by RAYTAC ( https://www.raytac.com/product/ins...
When I tried to send data in the form of float it shows an error and I changed it to another format as sending flag, mantissa(3 bytes), and exponent (1 Byte). Can anyone help...
To the kind attention of Nordic support team,
I have got an nRF52840 working application using usb and gazell, and I'm porting it from nRF52840 to nRF52833 these days. Yes...
I have some nRF52832 devices that have been flashed with a Softdevice v13 based firmware and can receive OTA firmware updates. Unfortunately their enclosures are sealed and...
Hi,
I am attempting to get the adxl362 sample working with the nrf9160 dk board. I am using the nordic SDK v1.2.0. I cannot get it to compile, compiling the code below fails...
Hello,
I am using SDK SDK_15.3.0_59ac345 in application that receives data from UART, and the aplication is running in background just ADV.
In the main function, after...
Sir,
With reference to the subject cited above the undersign is working as Assistant Professor in CSE Department and doing R & D in IOT.
I want to recommend your product...
Hi There,
ISSUE:
New Nordic Thingy:91 will not connect to the LTE network, it is giving:
2020-03-25T18:10:10.221Z DEBUG modem << cloud_connect failed: 22 \x0D\x0A...
Hi,
I'm working around to integrate FreeRTOS to Libuarte example, but i'm getting an error while building the project says:
For the Libuarte instance i'm using RTC instance...
Dear Sir,
I want to do the following scenario.
Once I power the device it will start advertising.
Now the advertising duration is 2minutes.
I have written...
I have a nRF52832 dev board and a separate J-link programmer. I want to do a sanity check on the programmer and I was wandering if there is a way to program the dev board...
I'm studying to perform DFU Peripheral from Central both using nRF52840, I'm able to issue command to let Peripheral into DFU mode, but got a "Received a fault" message in...
Hello,
I am using nRF52832 chip for freeRTOS project and using RTC2. I have SDK15.2. I want to have timestamp from RTC as hex format. I searched almost all forums but i...
