Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
The default I2C address of my sensor is 0x29 (7-bit).
If the least significant bit is low (0x52) the message is a master write to the slave. If the lsb is set (0x53) then...
I'm using SDK 12.2.0 with softdevice S130 V2.0.1 and want to use TWI.
Using the ble_beacon example I added the twi code from twi_sensor.
Shortly after calling TWI_Init(...
Hi,
during normal operation, my device shows a power consumption of 4.7mA.
Normal operation is:
accelerometer (lis2dh) detects a shake and wakes up the nrf51 via...
Hii ,
i am using customized board (chip : BT832).
err_code = sd_softdevice_enable(clock_source, softdevice_assertion_handler); hangs. it took some delay and after that...
Hi all,
I have seen a pair of questions ( this and this ) that I think have something to do with this, but didn't find a solution.
I have a custom board with a button...
I want to have an application similar to UART in the SDK example, with multiple peripherals.
I tried to modified existing UART example, but cannot make the central node...
I want to add the nrf52832 to my customized board and I am studing the possibilities for flashing it once that is located on the board. Is it possible to flash trhough the...
I have a board with some LEDs that are driven in the same way as with the nRF51 DK board (i.e. there is a resistor in series with the LED and you drive the pin low to turn...
In our testing we encounter some devices (Centrals with nrf52832), where the peer manager event PM_EVT_BONDED_PEER_CONNECTED contains a invalid peer id 0x4000 (allowed values...
I have a device the uses MSP430f169 and CC2500 RF controller for communication I need to replace the CC2500 RF controller with nRF51422 device.
As I understand an nRF51422...
Hi,
I develop application on MBED platform with NRF52-DK. I figure out that pin "logic" on this board is interchanged. For example. I have LED connected to some pin. When...
Hello,
on my custom board I am trying to use pin P0.09 and P0.010 for interrupt-purposes. So I integrated the necessary adjustments as mentioned in this topic here , which...
Hi,
I develop application using BLE.
In my scenario two NRF52832 operate in two different roles (Client and Server).
I have ready to run app (as server) and can communicate...
Hi,
When I call nrf_drv_spi_transfer to transfer 250 bytes in non-blocking mode, it takes 1.1ms. Is this normal? Any workaround? If it is normal then I have to split my...
My android app give me this "register with gatt stack failed" error on Samsung S7 marshmallow. The scenario is that I am working with 21 BLE peripherals (nrf52). I scan available...
