I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi Nordic DevTeam,
What I have learned from this thread below is that using 32kHz external crystal provides less power consumption and better accuracy :
https://devzone...
To the kind Nordic support team,
We are evaluating a scenario where we need a "gzll gzp host" to receive data on two encrypted pipes at almost the same time (we modified...
i was running some power optimization and MTU tests in NCS V1.5.1 and was able to compile and run.
I upgraded to NCS V1.6.0 and there were several errors
So when I compile...
Hello,
I am currently working with the development board nRF5340DK in order to evaluate the nRF5340 SoC.
Given certain project requirements related to the operating temperature...
Hello,
I am new on Nordic controller platform and i want to make the GPIO pull down and pull up at run time and also change the IO direction.
How i can do that please...
I am using the FAT FS on the nRF9160-DK to store data on an SD card.
The CLIB library provides Linix-like fopen, fclose, …
The flags passed to fopen are strings like ...
hello,
i am using nrf52832 with sdk 15.2 using ble_app_uart example and my beacon stops axdvertsing after sometime can someone help me how can make it advertise continosuly...
I am currently evaluating nrf52840 - CDSENET E73-2G4M08S1C module with installed CircuitPython 7.0.0-alpha.3. Unfortunately the ADC readings are quite noisy. For example for...
Hi, i'm using hte Keil and a custom board with NRF51822. The question is where i can read the value of a custom service? I make the configurations like this tutorial ( http...
Hi,
I have an application where it would be beneficial to be able to send get and set messages to individual groups, nodes elements, etc. All of which are not necessarily...
why doesn't the mesh chat example work on nrf5340?
I know it's not included in the list of supported platforms, but I'm trying to figure out why.
I can compile and upload...
Hi,
I've noticed that when I'm not initialize BLE stack, I have a failure in nrf_sdh_soc_evts_poll function (NRF_ERROR_NOT_FOUND).
Can you please explain what is the reason...
Hello:
nrf_pwr_mngt_run() doesn't always work on my custom board. About 1 time in 3, in code (I'm running in debug mode and using RTT) spits out
ERROR 3735928559 [Unknown...
