Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
I developed a software based on Blinky. I have been trying to add DFU to the current iOS app which is working properly to be like the Android app.
As I did in Android, the...
Hi, I would like to skip pairing process alltogether and just provide the KEys which were generated for both devices beforehand. My question is only. Is it possible to initate...
I have an application that will have up to 20 devices communicating with a gateway. Each device will need to send around 2MB of data every 5 minutes. We would like to use...
Hello.
I try to BLE and GPIOTE.
The reason for using GPIOTE is to read data from the temperature sensor.
And I want to sending data of temperature sensor by BLE...
Which type of PCB antenna should i use for BLE beacons based on nRF52832, nRF52840 and nRF52805 for longer range applications.?
Can i use the same antenna used in nRF52DK...
Hi All,
There are few chips that Nordic supports Direction Finding.
nRF5340,
nRF52833
nRF52820
nRF52811
Is it possible to know the recommended chip I should...
hi all,
NRF_ERROR_INVALID_STATE is coming when i initialise Ble_stak_init form nrf_sdh_enable_request() function.
I initalised ble once and disabled using sd_softdevice_disable...
Hello,
I am developing on the Garmin LIDAR-Lite v4 , which uses an nRF52840 internally with the programming pins exposed. I am able to run my OpenThread application on this...
Hi
while developing I've discovered that the current tickless implementation using RTC causes the idle task to loop for one tick before waking the next task up.
I've instrumented...
Platform: nRF52840 { development kit } SDK: nRF5_SDK_16.0.0 Can sdk_config be used to remap any pins for used a SCK and MOSI and MISO? Specifically, can the following mapping...
Hi all,
I'm running into this error when trying to compile anything for the SPI library in Cmake
CMake Error at ../../../cmake/extensions.cmake:372 (add_library):...
SDK v16.0 NRF52832
Hi
We have been using the the NRF Bootloader for sometime, but we have encountered an issue where if the DFU (Serial) is interrupted (ie, USB cable...
Hi,
I've been using the Thingy:91 to communicate with some sensors. One of this sensors is causing us some trouble: sometimes the I2C communication with him seems to fail...
Hello
I would like to commission my Thread network but my Thread network is isolated (I have no wifi) but I have bluetooth which works in parallel to the Thread network...
