I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I'm using nRF51822 chip and SDK 12.3.0 library to develop the software. We want to control the motors with PWM. But since PWM consumes a lot of power, we decided to...
Hello.
For My personal project , i would like to develop a buttonless OTA DFU on my Red Bear Nano V2 (Based on nRF52832 SoC Chip) . Im using the SDK11 and i have folloawed...
I'm trying to add RTT support into the secure BLE bootloader to get debug logs, but after adding the files it's consuming too much flash:
Is there any way to fit RTT support...
Hello,
I tried copying code from twi_sensor example to ble_app_uart and got this error:
Error[Li005]: no definition for "nrf_drv_twi_init" [referenced from W:\MODIFIED_SDK_13...
It takes time for fs_event_handler to be called back after nrf_fstorage_erase is executed. In SDK13.1.0, it didn't take much time, but in SDK15.3.0 takes time to be called...
Hey,
I am using nRF52840-DK and SDK 15.2 and working on 802.15.4. The transmitter is sending beacons at an interval of 2sec. The receiver is scanning the network for beacons...
It seems that the GPS is more inclined to give a fix faster when the trigger defined has type GPS_TRIG_FIX set than if the trigger type is GPS_TRIG_DATA_READY. Is this the...
I am working with a custom board and the nRF52840. I have been able to program various hex files to the Nordic chip on this board using SWD and an official Segger JLink device...
I am using the nRF51822 Development kit USB dongle to try to sniff a BLE connection between two other devices. I have installed Wireshark, flashed the firmware onto the dongle...
Hi,
Couple of questions:
- I'm finding that querying the Modem clock with AT+CCLK? always returns the network time the instant after it has registered with the LTE network...
How to increase the sig sensor model to have the data of the incoming sensor, why the development difficulty is so high. How do officials treat developers as enemies.It was...
I have troble when try to change custom service to Environment Sensing Service in this sample
https://github.com/maidenone/custom_ble_service_example
I used the sample...
hi,
I have some questions from test ble speaker (ex: JBL, Sony) or Air Pods.
First of all, I use two iphones to bond one airpods or ble speaker. (Below let me call two...
Hi,
Our application includes implementation of capacitive touch sensor through SAADC.I should initially wake up device from system off mode.Using SAADC is it possible to...
