I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hey all,
I was curious to see if anyone else is seeing the same problems I have with DFU.
I'm currently running SDK 15.2 and version 1.8.8 of nRF Connect on iOS. When...
Hello,
Previously I was using nRF52 SDK V11, printf did print properly and provided linefeed with '\r\n'.
Now I started using SDK V15, printf is no longer supported and...
I'm developing a nRF52832 based HID device and I'm at a bit of a loss as to why it isn't working on iOS. The device works as a keyboard fine on macOS, and it connects and...
Running nrfjprog 10.3.0 on macOS 10.14.6 (18G87) with an nRF52 dev kit
Occurs on all 10.x releases of Nordic command line tools. Other switches such as -i work.
edit...
Hi, I installed the nRF connect SDK, but get the following problem when trying to open the asset tracker project:
If I press ok, I see this:
Any ideas about what...
I use nrf52832.
Document written,
-------------------------------------------------------------------- RX current comsumption is IRADIO_RX0 Radio RX@1Mb/s BluetoothLowEnergymode...
Hello,
I'm trying to use raspberry pi to program nRF52832 on mass production. Because it's easy to do some test job with raspberry pi.
But there are still some issue I...
I want to achieve: 1. Mobile application networking with multi-lamp mesh 2. After mesh networking, many smartphones control all lights independently through proxy nodes. I...
Hi,
We are using nRF52832 based module on which we are using HCI over UART functionality with the help of Zephyr(v1.14.0) SDK to find the nearby beacons via Bluez stack...
Hello there,
So we are working with a sensor that needs to receive a pulsed voltage, so we are using a PWM signal from our nrf51-DK applied to a transistor based circuit...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the nRF5 SDK v15.3.0 and modified twi_sensor_pca10056 program...
Dear support,
We have built a ble mesh network running the light_switch_client/server application (mesh sdk 3.1.0). We are using the Android application for provisioning...
I want to disable and enable interrupts for Rx data, I tried following code to disable interrupt for rx and disable rx. Also TX and RX pins are short, i.e. loopbacked. In...
