Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi,
I'm trying to use the nrf_drv_spi.c to communicate with a BL652 + MCP2515 CAN SPI custom device. I've connected the MCP2515 to the nRF52832 (BL652 module) in the following...
as others have described I run the sniffer
than go through pairing process, the encrypted packets show up as "Encrypted packet decrypted incorrectly (bad MIC)"
is there...
Hi.
currently i use the nrf connect with a dongle to connect to a ble device to read/write characteristics for testing purposes.
Now i want to do it automatically using...
Hi all,
I am adapting some examples according to my needs and have encountered something that I find strange. I am trying to send 244 bytes from computer to usbd_ble_uart...
I want to program my nRF52832 Over-the-Air but not through Bluetooth. We have a Wi-Fi chip interfaced with nRF52832 so that the device can be connected to the internet.
I am trying to read the current time using CTS. I used the example source provided by nordic. However BLE_GATTC_EVT_READ_RSP does not occur in ble_cts_c_on_ble_evt.
BLE_CTS_C_EVT_DISCOVERY_COMPLETE...
Are there any examples of sampling something like an I2C bus at a constant sample rate? I have seen issues myself with the k_sleep and k_busy_wait not giving accurate delays...
nRF5_SDK_15.2.0_9412b96
soft device: s140
Compiler SEGGER Embedded Studio
1. I have used example ble_app_uart. I connected the ble module to a device which has a baud...
Hello,
I'm looking for a little clarification on how the antenna tuning circuitry works on the Thingy:91 v1.0.0 board.
From a previous topic on the DevZone, I saw that...
I'm having an issue where I can't reconnect to a device after updating the firmware from the iOS SDK. I believe it's the issue described here in the documentation:
Since...
I am having responding to an authorized write request. It seems to work for BLE_GATT_STATUS_SUCCESS case but any time I try to set the gatt_status to an error, the call to...
https://www.youtube.com/watch?v=wa_ARkZSr_U
This video presents how Bluetooth mesh network works . As we can see this network contains nine Thingys and one nRF52 DK (not...
I am now experiencing such a problem. I packaged 20 packets of data, each packet of data is 13 bytes, and then I want to send it out, but only 4 packets of data can be sent...
Hi everyone,
for a project, we need to interface an analog sensor which is not using standard protocols like I2C or SPI.
Instead, it uses 6 pins to receive commands...
