Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hi
There are two PCA10090 DK boards. Each one had its own iBASIS card.
Previously, I registered these two in nRF Connect for Cloud. DK board A with SIM card A.
DK board...
I have ordered some PCBs which have I2C lines on P0.08 and P0.09 and have been trying to test using the Dev Kit and for some reason, I can't get any traffic out of these pins...
Hello. I want to add OTA DFU feature to my device, based on nRF52810. I already met problem with not enough space on this chip, but it was solved, so I hope it possible to...
nRF52832 will restart accidentally, I have checked code, but I haven't fixed it so far;
Because restart is random, it is hard to reappear;
my question is
1, How do I...
Hi Sir,
My project need LESC & AES-CMAC function, then I enabled below CONFIG in sdk_config.h :
NRF_CRYPTO_BACKEND_MBEDTLS_ENABLED
NRF_CRYPTO_BACKEND_MBEDTLS_ECC_SECP256R1_ENABLED...
Hi,
So I am trying to configure the stdout console to use UART1 by default. Using the NrfConnect menuconfig in Segger emStudio I can set it to use UART1 with the following...
Hello !
I have read in DevZone, but still not sure regarding nRF52832 .
For nRF52832 and page size 4k, and regarding only writing zero-bits.
Can I in same page perform...
Hi team,
Here is the previous ticket
https://devzone.nordicsemi.com/support/234693
One of my customer TMC is using our nRF52810 in a BLE key project for central role...
When in dfu mode (with usb dfu enabled) if we jump to application via "
nrf_bootloader_app_start" there seems to be an issue where the firmware locks up and doesn't start...
Hello
my setup is a nrf52840, the sdk15.3, Softdevice s140.
is there a possibility, maybe with freertos, to to run two seperate applications like two threads.
In the...
Hi,
I'm trying to implement a slow timer which is supposed to be triggered about every 30 minutes or even less frequent, but I'm kind of clueless how to solve this issue...
from which antenna these values were derived resp. measured? e.g. there is a pcb antenna and a hirose u.fl connector available on pca10040... examples/ble_peripheral/ble_app_eddystone...
hi,
The software version is nrf5SDKforMeshv310src and nRF5_SDK_15.2.0_9412b96
I use five nRF52832 nRF52 DK. client * 1, server * 4, provisioner by android phone.
examples...
Hi can you help to configure nrf52840 DK board to measure power consumption with keysight n6705C. In manual is described with ammpermeter and oscilloscope. Keysight n6705c...
