hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello! I'm trying to use an external module with the VSC extension and I don't think that is currently supported (or easily supported.) For reference, our module works with...
Hello, I'm trying to manage connecting to my board (nRF52840-DK) which direct advertise (low prio) with peer address set to MAC address of my PC running Linux with bluez 5...
Now I have a problem, the transmitting power of NRF52810-QCAA is too low, only -2.73dBm. I tried to adjust the value of the capacitor, but the effect was not obvious. Excuse...
Hi, I tested the RGB Led (with an external RGB Led) with the nrf 5340. But I didn't find any pinout with a brief overview of all the pins and their features because the PWM...
I'm trying to setup the SAADC, I do this as much as possible without examples, so I really understand what is going on.
Setting up:
After this I try to start an ADC...
Hello DevZone,
I am trying to build a NFC driver but I am getting issues with it reinitializing every time I detect a field.
I am unable to use the T2T and T4T libraries...
Hi,
nrf52833 custom board
My query is that how to do OTA DFU on ble central devices (we are using nrf52833 as receiver dongle(ble central) device)? Does anyone advice...
Hi all,
when I follow the blog as below, find the actual output is not same as expected.
Adding a Peripheral to an NCS Zephyr project - Peripherals And RF Test - nRF Connect...
Hi Everyone,
I recently purchased the NRF52840 DK with a PCA10056 designation. I connected the DK to my Windows 7 laptop via the USB. This resulted in the JLINK(D:) drive...
I have a custom board with a nRF52805 module but I don't understand how the SDK works.
I followed some guide to simulate nRF52805 software, I had to patch some files in...
Hello,
I add sd_ble_gap_phy_update() in the ble_evt_handler() as below:
case BLE_GAP_EVT_CONNECTED: { ...... ble_gap_phys_t const phys = { .rx_phys = BLE_GAP_PHY_2MBPS...
The CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_FULL_SWING=y Kconfig option causes kernel booting to hang at line 505 of clock_control_nrf.c.
This is on the v1.7-branch of NCS ...
