I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I want to develop the nRF series at segger embedded studio for the first time. But I tried the following homepage to install manually. www.nordicsemi.com/.../Segger-Embedded...
NCS(nRF Connect SDK) is a good environment to develop nRF52,but it seems not stable until now.
I want to use NCS(nRF Connect SDK) to develop my project ,and met some unknown...
Hi Supporter,
I use apptimer in proprietary_rf gzll, I used as below ,but it doesn't work.
1) app_timer_init(); ,here I ennable the RTC1 in the sdk_config.h
2)app_timer_create...
Hello NRF ,
I have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure my network SIM as well as the NRF cloud .
I have used SDK 1.4.2...
Hello There,
Basically I just want to get Sensor data like (Temp Sensor) who already connect to Arduino and I get it , So I just want that data to nRF9160 over UART in...
Refer to nRF52840 Technical Manual USB 2.0 (full speed (12 Mbps) controller) The USB2.0 rate can be up to 480Mbps. We have a product whose USB transmission rate must not be...
I have created a program code on the Adafruit nRF52840 express in the Arduino IDE. I want to read this program code (including bootloader) via my j-link edu mini and save...
I noticed that the nRF Connect SDK has kept up with ZBOSS updates throughout the year. Is there a plan or recent releases with regard to the "nRF5 SDK for Thread and Zigbee...
Hi! I'm working on a custom board with nRF9160, I want to flash it with the asset tracker sample, however, I do not own a J-link device. What I have is a FTDI USB-UART converter...
My Thingy:52 is version 1.01. I haven't used it for a while and after charging, it didn't seem to be advertising. It was soft-flashing a green LED. I decided to program it...
Hi,
i am working on nrf52dk. i want to include "pwm" example in "ble_app_uart" example . i have included all the header files. and functions in "ble_app_uart" example. ...
Hi,
what is safe temperature range for nRF52840 - nRF9160 UART communication on 115200 baudrate without external crystals for HF clocks please ?
Thank you.
Hi,
I'm trying to program a custom board with a nRF52810 via nRF Connect. I keep getting the following error messages:
I followed this post and tried the following commands...
Hey guys,
I have nrf52832 custom Bluetooth module. It is stand alone nr52832 module . I just want to toggle any gpio on this module .
Can you guys tell me which library...
