hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello, I want to use Multiple Connection (Multiperipheral sample) to connect with multiple IOS phones at the same time to implement UART. Currently, up to 9 units are set...
I am trying to advertise the shotend name of the device no the complete local name, so code looks like follow
After scanning I can still find the name in the advertisement...
Hello, we are using nordic SDK 16.0 and mesh SDK 4.2.0.
In our project, sometimes at the start of the program, we are running into line 280 of mesh_config.c, a debug assert...
Hi, I am using nRF Connect SDK 1.5.1 with the nRF9160 Modem Firmware 1.3.0
I have implemented an application on the thingy91 with the gps driver (continuous mode) and the...
Hi,
I want to build a mesh network which includes least 12 server node an 1 client node.
I used light_switch example to send 12 byte message packets to client node from...
Hello, in my project i simultaneously use MPR121 touch sensor controller and GPS module connected to UART0 of nRF52840 (custom board). To handle touch events, i use MPR121...
Hello to all! I am trying to implement a device that can send keys from the code table 0x07 and a context menu key to the device. Here is my descriptor:
The first part...
I am using this Low Power Node example . Friendship works, however if I terminate Friendship and try to connect to LPN conventionally (via other proxy node) it does not work...
Hi,
I am working on programming a bootloader to have DFU capabilities. I have been using the secure_bootloader_uart example for SDK 15.3.0. I have modified the code to send...
I'd like to be able to use nrf sniffer tools (wireshark and nrf52dk) to listen to ble traffic after connection of two devices.
Is this possible?
Has anyone else done this...
I've read many similar issues that were raised regarding high SPI power consumption, looked at various examples, but can't seem to find any issue that is close to what i'm...
Hello.
When going to sleep with the BLE connection established, the WDT counter will be added. (WDT behaviour: NRF_WDT_BEHAVIOUR_PAUSE_SLEEP_HALT) At this time, my app cannot...
In the usbd_ble_uart example (SDK 17.0.2), I'd like to use the buttons handler module (the same one from the BLE Blinky example), instead of the BSP BLE button events. In...
