I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
I have a service with 2 characteristics, TX and RX. On TX the notify is enabled, because TX should send a notification when something changes. I manage to change what is needed...
Hello everyone.
We have a design based on NRF52840, which uses the built in USB peripheral and was fully tested and prototyped using NRF52840-QIAAD0-2031MR. We have now...
Hi There,
I have downloaded the nRFgo studio and nRFgo SDK and other files found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series
...
For the MPSL/timeslot example in NCS 1.5.0, I am trying set up a TIMER0 compare interrupt to take clean-up actions before the timeslot ends, as suggested in here . However...
Describe the bug Attempted to use the samples/bluetooth/hci_usb/ project with CONFIG_BT_EXT_ADV=y CONFIG_BT_EXT_ADV_LEGACY_SUPPORT=y CONFIG_BT_EXT_ADV_MAX_ADV_SET=4 CONFIG_BT_PER_ADV...
Hi, I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832 using...
I'm already using nrf51 in a project and now I need to make a DFU with BLE using a gateway. For the gateway project, I was thinking of using a nrf5x to implement a DFU master...
Hi , a day ago i recived my first dev board from nordic semiconductors, the nRF5340 . Until now I only coded for AtMega328 , esp32, esp8266 and other microcontrollers like...
I am trying to build the aws_fota example project for the nRF9160 using the nRF Connect SDK and the Segger IDE. We currently have v1.5.0 downloaded. The project is not compiling...
Hello everybody,
i use two nrd52 dk boards with nrf mesh light server flashed on them (mesh sdk 4.2.0)
They are configured over nrf mesh app to be in the same network...
Hi, I have nRF52840 DK. How can set the max range? or how can increase/decrease the tx range? Also is there any range extender to improve range? Thanks!
Hi,
I am currently doing a uart dfu over 2 nrf 52840 dks on a Windows PC. I have been using the example found in ...\examples\dfu\secure_bootloader\pca10056_uart_debug supplied...
Hello,
I am porting the secure serial bootloader from the nRF52833 DK (PCA10100), in which it works fine, to my custom board. I press the button and turn my board on to...
Hello, all
Following this ticket ( Configuring ADC sampling rate and simultaneous reading from multiple channels. ), I found a great example code that sends readings from...
