I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Good morning,
I'm developing an app for NRF52832 SDK 15.3, SD 132 6.1.1 with NUS service. Moreover my app has DFU and Peer Manager with LESC JustWorks security and other...
Hello All,
I am working on an indoor positioning project where I want to send/POST request RSSI values to the server/frontend. So is it possible to send RSSI values to the...
Hello,
we have a problem with a BLE connection state function. We are working with an NRF52832 device and SDK 14. The device itself works in central and peripharel mode...
Thanks in advance for any advice!
We are developing an ultra low powered network. There will be a remote control with numerous buttons. This will connect to 2-10 peripheral...
hai , I would like to program cli uart in pca10059, what are all things to change in openthread stack in order to change UART pin configure and how to compile it ? I use only...
I am trying to implement cli uart in custom board, for which there comes need for me to recompile openthread stack (in order to change UART and LED pin configuration) in GCC...
I was just working with the ble_app_uart example in nrf5_SDK_12.2.0. Minor modification were done to the main function. The build output:
linking...
._build\nrf52832_xxaa...
The site is just showing a product brief PDF, where can I access the full datasheet? Is the crystal oscillator on board or an external connection is required?
Hi,
I am using SDK version 15.3.0. I am trying to implement the ble_dfu example. By default, advertising name is set to "DfuTarg". I want change this to a custom name. How...
I'm using the nrf52840 with connectivity firmware and S140 SoftDevice, accessed through pc-ble-driver version 4.1.1, with NRF_SD_BLE_API=6
Occasionally pc-ble-driver fails...
Hi,
I am trying to find RSSI of the value of the nearest device also I need the Device name, address of those devices. I got the RSSI value but some problem in D evice name...
I'm upgrading a project from SDK 15 to SDK 16. Previously in my gap parameters init I had this code
This works fine for seeing the peripheral and operating it as a UART...
I wasn't sure which product to put in. I am looking for a BLE discovery tool for EEG devices -- particularly the Muse 2 Headband. Which of Nordic's software should I use for...
Hi,
In our project, we are using a small RTOS to switch between simple tasks and set MPU. We would like to run all task in unprivileged mode, but some Nordic SDK libraries...
