i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
I'm running a nRF52832 connected through TRACE port to a Segger J-Trace Pro.
Some traces seem to be lost, and Segger support team tells me it is possible as nRF52832...
I have a few questions regarding AoA mode.
My goal is to append the CTE frame too a standard advertisement frame. I would like to use one of the following examples as the...
Hardware: nRF52840, running on dev kit PCA10056
Software: SDK 15.0.0, no soft device
I'm trying to get the POF comparator working, and after struggling in our product...
I just updated my project from SDK 15.3 to 16.0. I am using the nRF52840.
I am not receiving the APP_BUTTON_RELEASE event when waking up from a button press. It used to...
I am trying to the asset tracking application on nRF9160DK and following the steps mentioned in https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hi there,
I have tried to build mqtt_simple but ı got an error says:
#error bsdlib must be run as non-secure firmware. Are you building for the correct board ?
I am...
Dear Support Engineers
I am in the process of designing the automated testing platform for a 52832 based device and would like to test to make sure the components/devices...
Hi, I am trying to test the examples provided in nRF5_SDK_16.0.0 on nRF52840 (PCA20035) thingy91 device. But unfortunately, i didn't see the support files for pca20035. For...
I am using nvs_init(), nvs_read(), nvs_write() calls to store and retrieve user data. Everytime I flash a new image I use the following commands:
# nrfjprog -e -f nRF91...
Hi!
I was wondering about the Receiver Category of the nRF52840 according to EN 300 328. The device should be classified as a category 1, 2 or 3 receiver, based on the...
Hello,
I recently bought a nRF9160 DK version 0.9.0, I did a few software experimentations on it and now I would like to restore the certificates properly.
I followed...
Hello,
I am new to cloud development and was wondering if there is any more documentation or tutorials on how to use the Device APIs for nRF Cloud in addition to the guides...
Dear Team,
why is that the command " AT+CCLK" returns time with 2hours of difference? How should one compensate?
AT+CCLK? +CCLK: "19/07/19,19:57:30+08" OK AT+CCLK? ...
Using a multimeter and a Thingy:91 I've measured the current to
The nrf9160 ( infocenter.nordicsemi.com/index.jsp
The nrf52840
The total (measured between battery...
Hi,
The following article describes how to perform serial programming of nRF9160 on Thingy91: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
