Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
We need to generate MCK of more than 10 MHz to achieve I2S connection between Nordic NRF5340 and MAX9867.
However looking at the data sheet there in no configuration which...
Hello,
We integrated latest released version of "pc-ble-driver.py" & "nrfutil" in our custom linux os running on ARM 32bit based custom board (B1).
pc_ble_driver_py :...
Hello Nordic,
We have an NRF52840 with SDK 16.0.0 as central in our project and multiple peripherals (which are IOS or Android phones) are supposed to connect to it.
In...
Hi,
I have a custom board using nrf 52832. I am using SDK 15.2.0 and softdevice s132 v6.1.0.
I have referred following link
https://devzone.nordicsemi.com/f/nordic-q...
I have a Nordic thingy 91 connected to nRF Cloud, and I see a message "Upgrade your firmware to view Network, Sim, Device, and Service Information" I have tried to update...
The nRF9160 is connected to the nRF52840 by MCU_IF0 ~7(GPIOs) in the Nordic Thingy:91. and I know to uses UART communication between the nRF52840 and the nRF9160. Can I know...
Hi
a way to reset nRF9160 is by pulling low the nRESET pin https://infocenter.nordicsemi.com/topic/ps_nrf9160/pmureset.html?cp=2_0_0_4_0_4_1#pin_reset
During the entire...
Hello!
I would like to try the following using my nRF52840 board: press a button on the board and then receive a notification on the phone. And the other way round , press...
I am trying to update the DUT(Device Under Test) via nrf52840 Dongle with PC(ubuntu16.04/windows10) by the command as below:
nrfutil dfu ble -ic NRF52 -pkg OTA_DFU.zip ...
Hi,
This is actually a followup ticket based on this: https://devzone.nordicsemi.com/f/nordic-q-a/56228/fota-dfu-over-internet .
Now the situation is a bit more concrete...
Dear all：
I want to control my central( 52840 ) device to connect with peripheral(52810) within a range （45-60m），i change the tx power，but it set -4dbm，the distance is just...
Hi, I'm developing new project, and during test I see that, if you quicly connect/disconnect/connect.... and so on, the app seems locked... Tu exclude my HW-FW, I tried same...
Hi,
How to auto-connect with my BLE peripheral without an external application?
Here, the Android mobile acts as a central, and the nordic chip act as a peripheral.
...
SDK15.0.0/SEGGER/Windows
Hi, I ran this example: https://github.com/NordicPlayground/nRF52-ble-long-range-demo .
Note: Added NRF_LOG_INFO("%s", p_adv_report->data.p_data...
