I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello,
Looking for some background info for SOFTDEVICE ASSERTION 0x0002715e. sdk 15.3, SD s132_nrf52_6.1.1
Maybe related, there is no Assert if fds_record_write() is done...
Hello
I am developing devices including nrf52832 and 3.3v buzzer. However, the buzzer in this device is very hot and the battery is running out quickly.
Now I know that...
Hi. I always appreciate to your kindness and fast reply.
I want to extend BLE range from 200m ~ 500m using FEM.
For the first time, I choose SKY66111 but it is not working...
Design background and goals,
1.Both ble_central and ble_peripheral are used nRF52832.
2.All nRF52832 UUID are the same.
3.Devices of different groups can’t be connected...
Hello!
I am having a problem using any internal flash writing libraries. If I set the REG0 voltage to 2.7V, the controller stops erasing the memory.
Moreover, I cant erase...
Hi,
I have seen that the pin for nRESET is selected on the NRF_UICR->PSELRESET register. I know that it cannot be modified from 0.21 on the 52832.
Can it be modified on...
Hi guys,
I am trying to figure out how to send the sensed data (temperature value) from the LPN node to the server node in the BLE mesh network. I have already found this...
I am using the nrf5340PDK and i am trying to have P1.04 trigger an interrupt on a high to low transition.
attached is my overlay file and my main.c to initialize the GPIO...
I made a code based on ble_app_uart_c which connects to a peripheral and once connected it can write or read data.
The code is supporting BLE4 (1M) and BLE5 (Long Range...
Dear Concern,
we have tried to configure the accelerometer LSM6DSO module through SPI interface using NRF52xx DK board. External Module was not configured properly...
Since the Online Power Profiler only supports 1M PHY, does a static power profile for coded PHY exist that shows the current levels for the full advertising length? I'd like...
hi
nRF5 SDK for Thread and Zigbee v4.1.0
need to build a simple sensor with analog input .
Referring to the simple sensor (binary input ), I did make a ZED simple binary...
i made a mesh network using cli ftd uart example and transfer data using udp portal
there comes a need for me to indicate reset command through switch and send reset command...
