hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
all set. while in linking stage i am getting
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_sdh_is_enabled (referred from nrf_fstorage_sd.o). .\_build\nrf52832_xxaa...
Hi,
I am using NRF51422 dk board in our project.We are using SDK 12.3 version , soft device S130 and keil u vision. Here the problem is I am not able to connect the bluetooth...
Hello:
I am able to debug and output to the J-link RTT Viewer(V6.44e) and when I stop debugging or sometimes randmley, the Viewer will display the message
"Warring:...
We're using SAADC to monitor two different voltage rails in different combinations (sometimes one and sometimes both).
I'm experiencing an issue in the following scenario...
Hi
I followed below tutorial, and I tried to send scan response data
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising...
Hi, everyone,
We are developing projects with nRF52832/51822 chips by using development board PCA10040. The programming of the chips is done by “nRF Connect\Programmer”...
Hi,
I have a problem with the app timer firing incorrectly.
I am using development board nrf52840-DK, Segger Studio 4.22, SDK 15.3.0_59.
When there has gone more than...
Hi
I'm really new to this filed and don't know anything about antenna, please forget me if the question is stupid.
I have an nRF52 DK, I noticed the Bluetooth antenna...
Hello, guys!
Here are the details about my development environment:
SDK = 15.3.0
IDE = SES
SoC = nRF52840-based BL654 module.
In my design, I need to drive a buzzer...
It's cool to have a build_all.sh script that supports so many cross-compilers. I've one more small request.
If run from a tool like CMake, the make tool does not pick...
Hello Nordic team
I am working on nRF52840 DK, SDK v-15.2, I am implementing directed advertising support and other side nRF52830 can capture this directed advertising data...
I'm trying to follow the instructions to install the nRF sniffer 2.0.0.
It appears that the .zip file (nrfsnifferforbluetoothle200c87e17d.zip) is missing the Profile_nRF_Sniffer_v2_001...
Hi,
Our application requires a Gazell device to be put into a 'slow' mode whereby it transmits a very short packet periodically but at a slow rate, e.g. once a second, until...
Hi,
I'm trying to compile the asset_tracker application and the at_client off the v1.0.0 branch, and I'm getting the error below:
cmedianu@ubuntumisc2:~/ncs/nrf/applications...
