Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Dear NORDIC engineers, excuse me. I would like to inquire about the Settings of NRF54LM20 APPPROTECT. I have modified APPROTECT[n].protect0 and APPROTECT[n].protect1 to 0x5A5A5A5A...
I am trying to use the nRF54L15 DK board to flash a Fanstel BM15M module.
Fanstel BM15M module link: Fanstel BM15M Module
I am using the nRF54L15 DK board with the external...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I have a nRF9151 dev kit for evaluation that I am following official guide to get up and running using the asset tracker v2 program. I can flash the firmware but I cannot...
I want to expand the flash allocated to mcuboot on the NRF desktop, but it failed to start after compilation
The following is a flash layout that can be successfully launched...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
I have successfully completed the one script install of Zephyr on RPI and can fully develop Nordic nrf52832/nrf52840. I assume all other supported boards within Zephyr can...
I'm trying to advertise an isochronous IN endpoint with wMaxPacketSize = 768 bytes (8 channels × 48 kHz × 16-bit audio, 1 ms polling). USB init fails at usbd_init with Failed...
Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
I measured the power consumption of the BLE RX using the nRF54L15.(nRF54L15-DK v1.0.0) 3.0V operation apps: scan_adv (delete advertising) west build -b nrf54l15dk/nrf54l15...
Hi Nordic Team,
I’d like to ask: Does the recommended Bluetooth matching circuit for the nRF54L15 need to be designed as a bandpass filter?
Also, do you have the VNA...
Hi devzone, I'm working on the nRF54L05, having an application and the mcuboot generated correctly on my host computer. Now we want to generate the binaries on Bitbucket pipelines...
Hi Nordic Support,
I am measuring the low-power current consumption of an nRF54L15 DK using a Power Profiler Kit II (PPK2).
In the nRF54L15 DK / Nordic documentation,...
While developing my project, I need to receive UDP packets with the NRF9151. My configuration is as follows: - 1nce SIM - VPN between my UDP service and the 1nce network ...
Hi
I use the light ctrl example from NCS 3.2.4 on the 52840DK v3.0.1, serial communication with an external MCU is required. After suspending the UART and disabling Mesh...
