hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Env setup:
nrf52840 on PCA10056, SDK 16.0.0, S140, FreeRTOS, secure bootloader
Description:
I'm trying BLE background DFU in the application.
Had reference iot/background...
Hi
Is there any implementatiaon of nrfutil, and more specifically the DFU via serial port, as a C library? My use-case is I need to update an nRF52840 from within an already...
Hi,
I am able to set up uart async receive, but when I try to set the call back using uart_callback_set() so that i can call the uart_tx() routine to push the data out,...
Hello,
I am working on nRF9160DK. I am using SES for ARM (Nordic edition).
How can I import new libraries for any project? Let's say I want to import SD card libraries...
Hi!
A little backstory on my project: Currently I have merged the saadc and peripheral ble_app_uart example. The value from a potentiometer is then sent over ble to the...
Hi,
I'm developing a project with nrf52832 sdk 16.0.0. I have some issue about the fds. peer_manager had used the fds modul, as we knew. And I would call fds_record_write...
I am looking at the APP_ERROR_CHECK and find out it finally goes to the app_error_save_and_stop method. I couldn't understand from the code, that where the error info saved...
I need the NRF58240 chip on my NRF52840 DK to operate at 1.8V (because I have some 1.8V only peripherals to connect to it) while I'm still debugging the NRF58240 using the...
Hello,
I am trying to run a sample program to setup the SDK and IDE with Segger embeeded studio.
I am getting this error. The Pathlenght is lesser than the 256character...
Hi, I have a Nordic 52810/PCA10040 DEV board with the latest zephyr.
In Zephyr configuration I using hardware clock option -> 32KHz clock source (RC oscillator)
I...
Hello, I'm getting started with my nRF52833 DK and have downloaded and licensed Segger embedded studio, and nrfConnect.
I believe I want to use the s140 softdevice. I'm...
I am just starting with the Nordic DK52. I am following the beginners tutorial for a custom service . But I am encountering 2 problems:
1) In step 4 it displays a RTT debug...
