I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Help ！
I use ANCS need change ATT MTU to more , but I met an incredible thing .
just change NRF_SDH_BLE_GAP_DATA_LENGTH to 189 & NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 185
...
Hi,
I was doing some current measurements and tried to reconnect my DK to my computer to put a new program on it. When I try to Connect J-Link, I get an error that says...
the link infocenter fail to download in:
(General PCB design guidelines for nRF52 series)
https://devzone.nordicsemi.com/nordic/short-range-guides/b/hardware-and-layout...
Hi,
Do you have a drawing of a recommended PCB layout footprint for the nRF9160?
I found a link somewhere, but the page didn't exist.
I need a drawing - not an Altium...
As i an trying to establish LTE connection using nRF9160.but i want to use external antenna because i will place nrf9160 module in metal enclosure. please suggest best antenna...
Hi pals!
I'm trying to do the throughput example with using 2 nrf52840DK. I downloaded SDK15.0.0 and I'm using ble_app_mtu_throughput example under ble_central_and_peripheral...
Hello there,
I've been following a guide Installing a 6LoWPAN enabled Linux kernel and required modules as a part of setting up a BLE 6LoWPAN border router on Raspberry...
I'm working on an NRF52832 product that will be intermittently powered, and the supply rail may fluctuate slowly, drifting above and below 1.8V.
I saw this post:
https...
Hello everyone
I am using nRF52840+wifi module to communication with the server via MQTT+LTS, Now MQTT communication with server was successful, Considering the safety,...
Hi everybody!
We have a problem with our product. It is based on nrf52832.
We used heart rate example in the SDK. MCU sleeps after a while if it is not connected. We have...
I'm trying to combine conventional pairing with OOB NFC pairing, but I'm struggling to decide which libraries to use. I have been looking at the examples, and they all use...
how can we properly set the scan timeouts? Say if we need to scan for a device for 5 seconds and if it is not available we can stop the scan and search for a new device. i...
Hello I am getting fatal error and system reset after calling APP_UART_FIFO_INIT.
I want to receive some data over ble and send it to the uart. I connected physical UART...
Hello, in my application I have a problem with the app_timer module respectively with a timer I have created. I'm working on a nrf52832 ( Rev. 1 - build code QFAA-B00) and...
I need a solution for doing a DFU from an Android phone to a device with a nRF52832 chip in it
I currently have a working version in IOS Swift but cannot get the Android...
