I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I've added a custom service for transferring data. It shall contain one characteristic that will notify when data is available, and the other should be a long read characteristic...
I recently got involved in a project where I am deploying a ble based mesh to understand and monitor bridge vibration patterns. I have been through nRF's mesh capabilities...
I am using the Arduino Primo board.
I have multiple beacons that advertise at a set interval.
All beacons have the same Device_name.
The Arduino Primo board scans for all...
Hello there. I just recently started programming using the nRF52832 DK, SDK14.1.0 and SoftDevice 132 v5.0 . I tried to follow this tutorial on Github: github.com/.../custom_ble_service_example...
I am using a power profiler to measure the timing of my program and I found something wrong. So I tested with a simple pure timer.
So first I set the timer during to 300ms...
I just spent 2 hours chasing BLE bug after upgrading from s132 v3 => v4.0.2
I added a call
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg)...
I couldn't use nRF Connect (BLE) under Linux, after updating the FW, it tries to open /dev/ttyACM0 but fails to do so.
Not a "permission" problem: the user is in uucp...
Hi,
I'm unable to compile the OpenMesh example application. I've modified the make file with correct paths. However I'm getting the following error. Can you please help...
I have a NRF51 talking through the UART to another uC, and I'm trying to log messages through Segger RTT. Everything works normally until I start to send some data through...
If SEGGER_RTT_CONFIG_DEFAULT_MODE is "BLOCK", the program won't start without RTT attached - at least for me... is there a possible solution?
I mean, technically it makes...
hello ,everyone
I was confused by a PWM problem for a long time , on nrf52832 SDK13 ,i wanna change the PWM duty cycle every period ,but now i find can not change it at...
Hey dear Devzone,
I am trying out some Thread and BLE dynamical examples on my nRF52840's but running into some problems using the " ble_thread_dyn_mtd_coap_cli " example...
Hello nordic dev community,
I am completely new to nordic products. I attended one of the conference and got more information regarding developer zone and info center....
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
