I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
In multi-link central app, after BLE_GAP_EVT_CONNECTED event, BLE_LBS_C_EVT_DISCOVERY_COMPLETE is called NRF_SDH_BLE_CENTRAL_LINK_COUNT number of times.
So For example...
Hi,
I use the original "nRF5_SDK_14.2\examples\ble_peripheral\ble_app_uart" no any modification, in Keil the .hex file size is 71k while it is 153k in SES.
My questions...
I am working on SDK V10.0.0 because I need S310 softdevice.
I like SEGGER_RTT I used in SDK V11 and V12.
But I got the Error in the subject line.
I had to uncheck use_microlib...
Hi,
I build below sample in SES and receive an error for:
Compiling ‘nrf_log_backend_serial.c’
can't open '...nRF5_SDK_14.2.0_17b948a/examples/ble_central_and_peripheral...
Hi!
There are many questions about flash memory already.
But I could not find the question I wanted.
I want to save scan data to flash memory.
However, when you...
As a peripheral,S130 can work ok,but when I add a central role, there is a error at central start to connect a peripheral. err_code = sd_ble_gap_connect(&addr,&m_scan_param...
When a peripheral advertises on one of the three advertising channels, does it listen for a short duration on that channel (as implemented by the Softdevice?) And then repeat...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit(PPK).
I used the following case with PPK setting.
infocenter.nordicsemi.com/index.jsp
At...
Hello Folks,
I am using PCA 10056 Eval board. I am using SPIM0 to connect 5 slave sensors. The Chip select is done by the UART Tx pin. So If I send 0x01 over UARt then...
Review_4Jan.zip
Hello All,
Please review the attached revised schematic and give your valuable feedback.
Please find below queries:
In case you want to know the...
Hii everybody,
I want to do ble pairing(nrf 52832 development board) with android phone. after searching on nordic devzone how to pair device i found that pairing mechanism...
Hello all,
I have below queries on my custom board and mesh.
I have designed my custom board using nRF51824 and i am using J link debugger for programming , I can able...
