hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
Arduino start selling Arduino 101, powered by an Intel Curie processor.
As far as I have seen here , Intel Curie module integrates nRF51822.
I was wondering...
I'm in the process of trying to start my custom application based on the ble_app_multilink_central_s130_pca10028 example found in the SDK. When I run the app on the nRF51...
Hello everyone,
I am trying to use Segger Embedded Studio for a simple explerimental project.
I started from the sample FDS example from github and build something on...
Hello,
I have an application that uses the Soft-Device. That application want to start a SPI-Bootloader. That SPI-Bootloader isn't the only bootloader on the device, so...
Hi,
I have nrf52 setup as central and peripheral.
As central it connects to another peripheral and everything works just fine. After it did connect I turn of peripheral...
Hi,
I have the NRF52 dongle that is set up as the client and is searching using the ble_app_uart_c (Found in examples\ble_central) example and I am trying to connect a...
SDK11, nRF51422.
Is it safe to use pstorage and fstorage at the same time?
I want to use fds for data storage in my firmware, but device_manager_peripheral.c requires...
Hi, I am trying to read a 24-bit register (with 8-bit address) using the I2C (nrf52). And the timing diagram is given below.
Basically I created a 3-element array (24...
I am having trouble getting the experimental ble_app_multirole_lesc example working with Android and nRF Connect. It is working fine in iOS. I am using v12.1.0 of the SDK...
hi..
i'm trying to use cmsis pack on nordic nrf52 with make command to get to cpu registers and have the folowing error:
Compiling file: main.c
In file included from...
Hi,
I was testing our product with PPK today and noticed one weird problem,- it seems that time is incorrectly displayed in the PPK software. Please have a look on the...
I have customised the ble_app_uart example for my application and the modified code works with the DK board. When I wanted to deploy this to the beacon board (pca20006), I...
I am using the SAADC on a NRF52 to read the battery voltage.
Everthing works fine on the NRF52 DK board but on my custom board I get around
the half of the real voltage...
Hi Nordic Semiconductor's community,
I have a question about the function sd_ble_gatts_value_set(), more precisely about if it is
possible to set the CCCD value of a characteristic...
