hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi
I tried to flash the softdevice with nrfprog, but it does not work. Even with nRFgoStudio it does not work.But with IAR I can program an example of the SDK (without...
Hello, all
I have a problem with ble data exchanging.
I have programmed an application which controls servo motors through phone application.
At the connection, ble...
Hi,
I am trying to use the SAADC to periodically sample an input from AIN0 and send the resultant data over a BLE link to a phone. Going through the forums I saw that the...
Hi,
I am trying to debug the blinky example project on the nRF52 development kit.
I have followed the following tutorial: devzone.nordicsemi.com/.../
Building and flashing...
I'm in the process of designing a circuit that requires Bluetooth. So instead of having a separate chip for Bluetooth and processing, I decided to use a Nordic Semiconductor...
Classic C documentation issue. Are the values that are passed by pointer (p_peer_address and p_whitelist) to sd_ble_gap_adv_start() copied into that function, or do they need...
I'm trying to read the 32-bit value of TIMER1, but it seems the value I read is always 16-bit value. When I debug the value is never above 0xFFFF.
snippet from nrf_drv_config...
The peripheral is actually a dual-mode device, with BLE being a peripheral device.
I can connect to this device and discover the GATT services with the nRF Connect iPhone...
What is the minimum and max value that the NRF_RADIO->TXPOWER register can get set to? The datasheet it takes a signed 8 bit for the setting, but what happens if you set it...
Hello,
I am trying to read data from nRF51422 ADC using SDK51 PCA10028 board downloaded with S130. I tried one of existing ADC with Softdevice examples, it seems to work...
I have meander antenna design on my board with matching network(similar to PCA10031).
Since I don't have access to VNA or Spectrum Analyzer for tuning antenna, I am tuning...
I'm building some code off of the twi_master_using_app_twi example which is available in the SDK (v11.0.0).
The two peripherals I'm working on are an accelerometer (LIS3DH...
I've just upgraded to Windows 10, and I've found that the PC freezes completely (i.e. no mouse movement, no keyboard response) when I unplug an nRF52 DK board. When I plug...
Hi,
In my application, I need 3 PWM to drive LED. Each PWM will have the same frequency but not the same duty cycle.
Is that possible to do that?
I know that Timer0 is...
hi
on android side of my project i try to disconnect from gatt by this code
mbluetoothGatt.disconnect();
but in nrf51422 this event not trigering
static void on_ble_evt...
